manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 364 of 760

•

 

Burst Mode, Level Detection

In the case of burst mode with level detection, the 

DREQ

 sampling timing is the same as in

cycle-steal mode.

For example, in figure 11.20, DMAC transfer begins, at the earliest, three cycles after the first
sampling is performed. The second sampling is started two cycles after the first. Subsequent
sampling operations are performed in the idle cycle following the end of the DMA transfer
cycle.

In burst mode, also, the DACK output period is the same as in cycle-steal mode.

•

 

Burst Mode, Edge Detection

In the case of burst mode with edge detection, 

DREQ

 sampling is only performed once.

For example, in figure 11.21, DMAC transfer begins, at the earliest, three cycles after the first
sampling is performed. After this, DMAC transfer is executed continuously until the number
of data transfers set in the DMATCR register have been completed. 

DREQ

 is not sampled

during this time.

To restart DMAC after it has been suspended by an NMI, first clear NMIF, then input an edge
request again.

In burst mode, also, the DACK output period is the same as in cycle-steal mode.

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

ZALMAN RESERATOR 1 Manual preview
RESERATOR 1
Brand: ZALMAN Pages: 22
Eaton APS6-400 Series Installation And Operation Manual preview
APS6-400 Series
Brand: Eaton Pages: 114
Optostar OP-8000-EDFA-1U Series Manual preview
OP-8000-EDFA-1U Series
Brand: Optostar Pages: 9
Lanner FW-7551 User Manual preview
FW-7551
Brand: Lanner Pages: 38
ivideon Bridge B1610 Quick Start Manual preview
Bridge B1610
Brand: ivideon Pages: 11
Rockwell Automation Trusted T8833 Manual preview
Trusted T8833
Brand: Rockwell Automation Pages: 21
National Instruments IMAQTM User Manual preview
IMAQTM
Brand: National Instruments Pages: 121
COUGAR Vortex SPB 120 User Manual preview
Vortex SPB 120
Brand: COUGAR Pages: 2
Cypress Semiconductor CY7C1381DV25 Specification Sheet preview
CY7C1381DV25
Brand: Cypress Semiconductor Pages: 28
Intel SRCSASPH16I - RAID Controller Hardware Manual preview
SRCSASPH16I - RAID Controller
Brand: Intel Pages: 28
Hologic ThinPrep 3000 Operator'S Manual preview
ThinPrep 3000
Brand: Hologic Pages: 256
Carrier 40VMW005 Installation And Maintenance Instructions Manual preview
40VMW005
Brand: Carrier Pages: 18
Qvis 72-8P Series User Manual preview
72-8P Series
Brand: Qvis Pages: 233
ATEN Altusen SN0100 Series User Manual preview
Altusen SN0100 Series
Brand: ATEN Pages: 178
PowerLogix PowerForce G4 '47 Installation Instructions Manual preview
PowerForce G4 '47
Brand: PowerLogix Pages: 12
Airaya AI108-1-050 Quick Install Manual preview
AI108-1-050
Brand: Airaya Pages: 28
VIA Technologies ARTiGO-A1200 Quick Manual preview
ARTiGO-A1200
Brand: VIA Technologies Pages: 2
Z3 Technology FV2K-DCK-1x User Instructions preview
FV2K-DCK-1x
Brand: Z3 Technology Pages: 94

Brands by name

Popular brands

Load more brands