manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 453 of 760

14.3

Operation

14.3.1

Overview

For serial communication, the SCI has an asynchronous mode in which characters are
synchronized individually, and a synchronous mode in which communication is synchronized with
clock pulses. Asynchronous/synchronous mode and the transmission format are selected in the
serial mode register (SCSMR), as shown in table 14.9. The SCI clock source is selected by the
combination of the C/

A

 bit in the serial mode register (SCSMR) and the CKE1 and CKE0 bits in

the serial control register (SCSCR), as shown in table 14.10.

Asynchronous Mode:

•

 

Data length is selectable: 7 or 8 bits.

•

 

Parity and multiprocessor bits are selectable. So is the stop bit length (1 or 2 bits). The
combination of the preceding selections constitutes the communication format and character
length.

•

 

In receiving, it is possible to detect framing errors (FER), parity errors (PER), overrun errors
(ORER) and breaks.

•

 

An internal or external clock can be selected as the SCI clock source.

 

When an internal clock is selected, the SCI operates using the on-chip baud rate generator,
and can output a serial clock signal with a frequency matching the bit rate.

 

When an external clock is selected, the external clock input must have a frequency 16 times
the bit rate. (The on-chip baud rate generator is not used.)

Synchronous Mode:

•

 

The transmission/reception format has a fixed 8-bit data length.

•

 

In receiving, it is possible to detect overrun errors (ORER).

•

 

An internal or external clock can be selected as the SCI clock source.

 

When an internal clock is selected, the SCI operates using the on-chip baud rate generator,
and outputs a serial clock signal to external devices.

 

When an external clock is selected, the SCI operates on the input serial clock. The on-chip
baud rate generator is not used.

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

GE 90-30 PLC User Manual preview
90-30 PLC
Brand: GE Pages: 93
Farallon NetLINE USB User Manual preview
NetLINE USB
Brand: Farallon Pages: 26
Observint N16 Quick Setup Manual preview
N16
Brand: Observint Pages: 11
3Com 3CRSHPW196 User Manual preview
3CRSHPW196
Brand: 3Com Pages: 16
IBA Com-L2B-4-8 Manual preview
Com-L2B-4-8
Brand: IBA Pages: 29
XtendLan NVR-xUD User Manual preview
NVR-xUD
Brand: XtendLan Pages: 228
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Brand: Balluff Pages: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Brand: MEMON Pages: 2
Moxa Technologies TAP-125 Series User Manual preview
TAP-125 Series
Brand: Moxa Technologies Pages: 51
AXIOMTEK FAB118-14B5P7 Quick Installation Manual preview
FAB118-14B5P7
Brand: AXIOMTEK Pages: 2
Microscan MS-96 Vial Reader User Manual preview
MS-96 Vial Reader
Brand: Microscan Pages: 67
NUROTRON CS-10A Operation Manual preview
CS-10A
Brand: NUROTRON Pages: 16
Analog Devices EZ-KIT LITE ADSP-2191 Manual preview
EZ-KIT LITE ADSP-2191
Brand: Analog Devices Pages: 98
SilverStone EXB02 Manual preview
EXB02
Brand: SilverStone Pages: 12
Thecus N5200BR User Manual preview
N5200BR
Brand: Thecus Pages: 90
PowerLogix PowerForce G4 '47 Installation Instructions Manual preview
PowerForce G4 '47
Brand: PowerLogix Pages: 12
Xilinx SelectIO 7 Series User Manual preview
SelectIO 7 Series
Brand: Xilinx Pages: 188
SeaLevel SIO-485.LPCI User Manual preview
SIO-485.LPCI
Brand: SeaLevel Pages: 19

Brands by name

Popular brands

Load more brands