PART 1: CX-Programmer
OMRON
CHAPTER 4 – Reference
CX-Programmer _Page 69
2. Select
the
Work Online Simulator
button from the toolbar. The simulator starts and
CX-Programmer goes on-line. The Download Options dialogue is displayed allowing
individual components to be selected for transfer to the PLC, for example, programs, PLC
settings, IO table, symbol tables, and comments.
Note:
When a program is on-line to a Simulator, the program will not be able to connect
to a PLC and other programs will not be able to go on-line to this Simulator.
Note:
CX-Simulator must be installed to operate this function. CX-Simulator is
supported for CS/CJ-series PLCs.
3. Set the settings as required and select the
OK
pushbutton. The items that can be
downloaded vary according to PLC series.
Select the
Work Online Simulator
button again to go offline with the Simulator.
Select the
Exit Simulator
option from the PLC menu to close the simulator.
PLC Operating Mode
The PLC can be set to one of four operating modes: Program, Debug (for CV-series PLCs only), Monitor and
Run.
♦
Program Mode
.
In this mode, the PLC does not execute its program/s. It is used to download
programs/data.
♦
Debug Mode
.
This mode is available on CV-series PLCs and enables basic debugging of user programs.
♦
Monitor Mode
.
This mode allows a running program to be edited and monitored while connected during
development. On-line editing must be performed in this mode.
♦
Run Mode
.
This mode sets the PLC to execute the current program as a live operation. This mode is
generally used for final testing, after a program has been thoroughly tested and debugged. CX-Programmer
cannot write to the PLC while it is in this mode.
Some software operations are possible only in certain modes.
Use the following procedure to change the PLC operating mode.
1, 2, 3…
1. Select the PLC object from the project workspace.
2. Select
the
Work On-line
button from the toolbar. A confirmation message is displayed:
select the
Yes
pushbutton to connect to the PLC.
3. Select
the
Program Mode
button, the
Debug Mode
button, the
Monitor Mode
button or
the
Run Mode
button from the toolbar.
Monitor in RungWrap
Monitor in RungWrap allows you to monitor long rungs, which exceeds the right bus-bar, in the length of the
initial position number of the right bus-bar.
This function is used when CX-Programmer is on-line. While online-editing rungs, the RungWrap will be
released and after online-edit is finished, the rungs will be shown as RungWrap again.
CX-Programmer should meet all the following conditions of monitoring rungs in RungWrap.
♦
Monitor in RungWrap menu is toggled ON.
♦
Show right bus-bar is checked ON (in Options dialog).
♦
The number of Initial position (cells) is set to more than three (do not set Expands to widest rung) in
Options dialog.
♦
The length of rungs in the diagram is exceeding the right bus-bar.
♦
CX-Programmer is online to a PLC.
♦
The program is shown as Ladder diagram (not in Mnemonics view or shown as Statement List).
♦
No error is found in the program. (Left bus-bar is not shown in red.)
♦
The program is not online-editing.
Note:
When the right bus-bar is not displayed or the number of initial position of the right bus-bar is
less than two, programs cannot be monitored in RungWrap.
Summary of Contents for Sysmac WS02-CXPC1-EV3
