PART 2: CX-Server PLC Tools
OMRON
CHAPTER 3 – IO Table Component
CX-Server PLC Tools_ Page 21
♦
Controller Link
. Allows the polling status of the node to be set (whether it is a polling or polled unit) and
whether to clear the Controller Link unit EPROM.
Use the following procedure to edit the Software Switch Setup.
1, 2, 3…
1. Highlight the rack/unit in the IO Table tree.
2. Click the right-mouse button and select
Software Switches
.
3. Set the required software switch setup options for the specified rack/unit.
General
The
General
tab of the Software Switches dialogue provides the complete software switches settings for a Basic
unit, PC unit, Mini-map unit, Host Link unit, Motion Control unit, ME-Net unit, CompoBus/D Master unit and
ISO Baud unit. It also serves as partial software switches settings for other units.
1, 2, 3…
1. Access the Software Switch dialogue for an appropriate rack/unit.
2. Set the required CIO and DM area address in the
CIO Address
field and
DM Address
field.
Data Link Area
The
Data Link
tab is used to control whether Data Link is generated automatically or by a specific Data Link
table for SYSMAC LINK, SYSMAC NET and Controller Link. This setup is only used if the Node Type is
Master. The list box at the bottom of the chapter is only used when Data Link is set to one of the automatic
options (i.e. not specific).
1, 2, 3…
1. Select
Transfer from PLC
from the
Options
menu to transfer the current system area
settings from the unit.
2. Select the required unit and click the right-mouse button. Select the
Software Switches
setting.
3. Adjust the settings as required.
4. Select
Transfer to PLC
from the
Options
menu to transfer the network parameters to the
unit.
5. Select
the
Reset Unit
setting to restart the unit - the written settings are activated in the
unit.
Note:
If the unit which is being set is the one on which the current communication to the
PLC is being made, the PLC needs to be closed and opened before communications
can continue.
Ethernet
The Ethernet setup differs from SYSMAC LINK, SYSMAC NET and Controller Link by not having a Data Link
Area setup and by having two further dialogue boxes, the IP Address Table and IP Router Table. This
particular interface requires that each device attached to the network has an IP address, and that routing
information for directing data across the network is also included (where necessary); such address information
ensures that data is transmitted correctly between two nodes.
Note:
Table information is only used if the
IP Address Conv.
Method radio button is not
set to
Auto
.
The File Transfer Protocol (FTP) allows access to a file card on the PLC. If a FTP login name and password
are entered then these are used to start an FTP session. For more information, refer to the Ethernet User’s
Manual.
The IP Address Table
dialogue allows the IP address of a network node to be entered.
1, 2, 3…
1. Select the Ethernet Unit from the IO Table and click the right-mouse button.
2. Select
the
Unit Setup
option.
3. Click on the
Insert
pushbutton.
4. Enter the IP Address for the node in the
IP Address
field; each of the four fields must take
a value in the range 0 to 255.
5. Select
the
OK
pushbutton to proceed.
6. Click on the
Delete
pushbutton to remove the address from the table.
Summary of Contents for Sysmac WS02-CXPC1-EV3
