PART 1: CX-Programmer
CHAPTER 2 – Quick Start Guide
OMRON
CX-Programmer _Page 24
On-line Edit
Although the downloaded program has been greyed to prevent direct editing, the Ladder program can be
amended by explicitly selecting the On-line Edit feature.
It is usual to have the PLC operating in Monitor mode while using on-line editing functions. On-line editing is
not possible in Run mode.
Use the following procedure to edit the program on-line.
1, 2, 3…
1. Select the rungs to be edited by dragging the mouse and selecting the required rungs.
2. Select
the
Compare with PLC
button from the toolbar to ensure that the edited area is
the same as in the PLC.
3. Select
the
On-line Edit Rungs
button from the toolbar. The background to the rung
changes to show that it is now an editable area. The rungs outside this area cannot be
altered but elements can be copied from these rungs into the editable rungs.
4. Edit the rungs as appropriate.
5. Select
the
Go to online-edit rung
to go back to the top of the on-line editing rung.
6.
When satisfied with the results, select the
Send On-line edit Changes
button from the
toolbar. The editing is checked and transferred to the PLC.
7.
Once these changes have been ‘sent’ to the PLC, the editable area becomes read-only
once more. The on-line edit can be cancelled at any point prior to committing the
changes by selecting the
Cancel On-line Edit
button from the toolbar.
Note 1:
A symbol address or type cannot be edited on-line.
Note 2:
I/O comments can be changed during online editing in Ladder diagram view, in the Symbol
Table, or in I/O Comment View. If I/O comments have been changed when online editing is
ended, a confirmation message will appear asking if the symbol table file should be transferred
to file memory in a CS-, CJ-, CVM1, or CV-series PLC or to the I/O comment area in the
allocated UM (user memory) in a C-series PLC.
Symbol table names and addresses cannot be changed during online editing.
I/O comments with symbol names cannot be transferred to the I/O comment area in UM (User
Memory) in C-series PLCs.
Attaching Comments
An attached comment is a comment associated with an element of a program (i.e. contact, coil or instruction).
The comment is entered through the Properties dialogue box of the element by selecting the
Properties
option
from the context menu of the item.
When a comment has been entered against an element, a circle will appear at the top-right corner of the element.
This circle contains a number that uniquely identifies the comment within the rung. The comment itself will
appear to the right of the circle for output instructions (subject to the chosen ladder-information options), or it
will appear in the Rung’s Annotation List.
Summary
In this chapter, the programmer has been introduced to the following concepts:
•
Starting the CX-Programmer application.
•
CX-Programmer and projects. The CX-Programmer environment, including the project
workspace, Diagram Workspace, Mnemonics view and symbol tables.
•
Getting started with CX-Programmer.
•
Setting up a Ladder program.
•
Writing a Ladder program.
Summary of Contents for Sysmac WS02-CXPC1-EV3
