PART 2: CX-Server PLC Tools
CHAPTER 4 – PLC Setup Component
OMRON
CX-Server PLC Tools_Page 30
Select one option from the list to set the execution mode. Choosing Not Specified will disable all the options
within the Peripheral Service dialog, except for 'Set time to all events'. Not Specified is the only way of setting
the Peripheral Service Execution Time to zero.
If Peripheral Service is chosen, editing Peripheral Service Execution Time is possible, and the system sets the
default to 0.1. See also Instruction Processing (Peripheral Service Execution Time).
Specifying Asynchronous will disable the same options as Not Specified, and set the Execution mode to
Asynchronous processing. Synchronous likewise sets the Execution Mode to Synchronous processing
Peripheral Service Mode
Instruction Execution Time
- A value within and including the range of 5 to 255 or 0 can be entered as a valid
setting.
Peripheral Service Execution Time
- A value within and including 0.1 to 25.5 can be entered as a valid setting.
For more information on when this option is available, see Sync/Async Comms, Execution Mode, above.
Target Unit (1, 2, 3, 4, 5) and SIOU
- The default for this setting is Not Specified. There are five possible
options for this setting. After Not Specified, the next option is CPU SIOU. If this option is selected, the
SIOU number should be entered in the box to the right marked 'SIOU'. The next option is SIOU, and likewise
with the CPU SIOU option, the SIOU number should be entered in the box to the right marked 'SIOU'. The
three remaining options allow either the Inner Board, Host Link Port or Peripheral Port to be set as the 'Target
Unit'.
Set time to all events
Set time to all events (default 4%)
- By ticking the checkbox, the default as stated above will be set. If the
checkbox is not ticked, then a value between 0 and 255 inclusive can be entered, effecting a maximum setting of
25.5 (255 *0.1). This option is found in the Timings tab for all other CS1 PLCs.
Duplex Settings
The Duplex Setting tab is activated by selecting the Duplex Settings option from the PLC Settings Options
menu.
With this option checked, use the Tabs scroll buttons to scroll to the right and click on the Duplex Settings tab to
bring it to the front. The options in this dialog can now be set to provide the appropriate communications setup
within the selected Communications Units. The dialog is divided into five sections as follows:
Note: The Duplex Setting tab is available for CS1H-H 65 & 67 PLCs but is only applicable to the CS1D series
PLCs.
Operation Settings
Run under Duplex Initial
– This option should be selected if it is required to run two Units in parallel with
Duplex Initial execution. Note that this setting only takes effect at startup or at the start of an operation. It
cannot be changed during an operation.
Return Automatically
– Select this option when it is required to execute a process that returns to Duplex
Operation automatically.
Communications Unit Duplex Setting
From the list of Communications Units select those that are to be run in duplex mode. If more than one Unit is
set to duplex mode the options selected will be applied to each Unit. It is not possible to set different options
for different Communications Units. To execute the Communication Duplex operation an IO table must be
Summary of Contents for Sysmac WS02-CXPC1-EV3
