Omron E5C series, User Manual

Page: 368 / 372

Index-4
E5@C Digital Temperature Controllers User’s Manual (H174)
Extraction of Square Root Low-cut Point ...... 5-47, 6-36
HB ON/OFF ........................................................... 6-63
Heater Burnout Detection 1 ................................... 6-22
Heater Burnout Detection 2 ................................... 6-23
Heater Burnout Hysteresis .................................... 6-64
Heater Burnout Latch ............................................ 6-64
Heater Current 1 Value Monitor .................... 6-10, 6-22
Heater Current 2 Value Monitor .................... 6-11, 6-23
Heating/Cooling Tuning Method ...................... 5-9, 6-85
HS Alarm 1 ............................................................ 6-24
HS Alarm 2 ............................................................ 6-25
HS Alarm Hysteresis ............................................. 6-75
HS Alarm Latch ..................................................... 6-75
HS Alarm Use ............................................... 4-42, 6-74
Hysteresis .............................................................. 4-21
Hysteresis (Cooling) .............................................. 6-31
Hysteresis (Heating) .............................................. 6-31
Initial Setting/Communications Protect .................... 6-4
Input Digital Filter ................................................... 6-66
Input Type .................................................... 6-42, A-21
input type ............................................................... 4-11
Integral Time .......................................................... 6-28
Integral Time (Cooling) ..........................4-14, 5-9, 6-29
Integral/Derivative Time Unit ........................ 6-29, 6-65
Integrated Alarm Assignment ....................... 5-24, 6-80
LBA Band ..................................................... 5-29, 6-77
LBA Detection Time ...................................... 5-29, 6-76
LBA Level ..................................................... 5-29, 6-76
LCT Cooling Output Minimum ON Time ................ 6-91
Leakage Current 1 Monitor ........................... 6-11, 6-24
Leakage Current 2 Monitor ........................... 6-12, 6-25
Limit Cycle MV Amplitude ............................. 4-25, 6-66
Loop Burnout Alarm (LBA) .................................... 5-28
Manual Control Level ............................................. 5-34
Manual MV Initial Value ......................................... 6-73
Manual MV Limit Enable ........................................ 6-84
Manual Output Method .......................................... 6-72
Manual Reset Value ............................................... 6-30
Minimum Output ON/OFF Band ............................ 6-85
Monitor/Setting Item 1 to 5 .................................... 6-87
Monitor/Setting Item Display 1 to 5 ........................ 6-38
Move to Advanced Function Setting Level ............. 6-58
Move to Calibration Level ...................................... 6-91
Move to Protect Level .............................................. 6-3
Move to Protect Level Time ................................... 6-69
Move to the Protect Level ...................................... 5-20
Moving Average Count ................................... 5-3, 6-67
Multi-SP Set Point Selection .................................... 6-9
MV (Manual MV) .................................................... 6-40
MV at Error ............................................................ 6-33
MV at PV Error ...................................................... 5-45
MV at Stop .................................................... 5-44, 6-32
MV at Stop and Error Addition ............................... 6-71
MV Change Rate Limit ................................. 5-49, 6-35
MV Display ............................................................. 6-67
MV Display Selection .................................... 4-50, 6-88
MV Lower Limit ...................................................... 6-34
MV Monitor (Cooling) ............................................. 6-16
MV Monitor (Heating) ............................................ 6-16 MV Upper Limit ...................................................... 6-34
Number of Multi-SP Points ..................5-11, 5-14, 6-61
Operation/Adjustment Protect ................................. 6-4
Parameter Initialization .......................................... 6-61
Parameter Mask Enable .......................................... 6-6
password ............................................................... 5-20
Password to Move to Protect Level .......................... 6-6
PF Setting ..................................................... 6-38, 6-86
PID ON/OFF .......................................................... 6-44
PID ON/OFF parameter ......................................... 4-22
Position Proportional Dead Band ................. 5-58, 6-35
Process Value Input Shift ........................................ 5-3
Process Value Slope Coefficient ............................. 5-3
Process Value/Set Point 1 ....................................... 6-8
Process Value/Set Point 2 ....................................... 6-8
Program Pattern ........................................... 5-39, 6-46
Program Start ........................................................ 6-12
Proportional Band .................................................. 6-28
Proportional Band (Cooling) ..................4-14, 5-9, 6-29
Protocol Setting ..................................................... 6-92
PV Decimal Point Display ...................................... 6-89
PV Rate of Change Calculation Period ......... 4-35, 6-84
PV Status Display Function ................................... 6-89
PV/MV (Manual MV) .............................................. 6-40
PV/SP Display Selection ......................................... 6-8
PV/SP No. 1 Display Selection ..............4-49, 6-8, 6-88
PV/SP No. 2 Display Selection ..............4-49, 6-8, 6-88
Remote SP Enable ....................................... 5-56, 6-81
Remote SP Input .......................................... 5-56, 6-81
Remote SP Input Shift ........................................... 5-56
Remote SP Input Slope Coefficient .............. 5-56, 6-28
Remote SP Lower Limit ................................ 5-56, 6-82
Remote SP Monitor ...............................5-56, 5-57, 6-9
Remote SP Upper Limit ................................ 5-56, 6-82
RT .......................................................................... 6-74
RT (Robust Tuning) ................................................ 6-74
RUN/STOP ............................................................ 6-13
Scaling Lower Limit ............................................... 6-43
Scaling Upper Limit ............................................... 6-43
Set Point During SP Ramp .................................... 6-10
Set Point Lower Limit ............................................. 5-15
Set Point Upper Limit ............................................. 5-15
Setting Change Protect ........................................... 6-5
Soak Time ...........................................5-39, 5-40, 6-31
Soak Time Remain ................................................ 6-13
Soak Time Unit ...................................................... 6-80
SP Lower Limit ...................................................... 6-44
SP Mode ..............................................5-56, 5-57, 6-21
SP Ramp Fall Value ...................................... 5-17, 6-33
SP Ramp Set Value ...................................... 5-17, 6-33
SP Ramp Time Unit ............................................... 6-61
SP Tracking ..........................................5-56, 5-57, 6-83
SP Upper Limit ...................................................... 6-44
SP0 to SP7 ............................................................ 6-26
ST (self-tuning) ............................................. 6-45, 6-65
ST Stable Range ................................................... 6-65
Standard or Heating/Cooling ................................. 6-45
Standby Sequence Reset ...................................... 6-62
SV Status Display Function ................................... 6-90