Minolta DI450 Service Manual Download Page 88

Page: 88 / 271

D-69

(2)

Adjustment of Front Door Interlock Switch

1. Swing down the Front Door.
2. Remove the Left Cover.
3. Slide out the Fusing Unit.
4. Remove four screws and the Cover.

NOTE

Do not remove the belt mounting screw on the cover.

4002D196AC

5. Loosen two screws that secure Front Door Inter-

lock Switch.

4002D197AB

6. If the interlock switch is OFF when the Front Door

is closed in position, move the interlock switch
toward the front.

7. If it is impossible to close the Front Door in position

because of the interlock switch located excessively
to the front, move the switch to the rear.

4002D198AC

8. After the Interlock Switch is moved, tighten two

mounting screws.

9. Check the Interlock Switch ON/OFF by closing and

opening the Front Door.

Reference

An NO type switch is used for the Interlock Switch.

4002D199AB

Summary of Contents for DI450
















































































































































































































































































Search results

Summary of Contents for DI450

Reviews:

Minolta DI450, Service Manual, Page: 88 / 271

Search results

Summary of Contents for DI450

Reviews: