manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 245 / 271

Share
Download
Minolta DI450 Service Manual Download Page 245

T-54

C0910, C0914

C0920, C0924

Step

Check

Result

Action

1

Lift-Up Motor turns when the 2

nd

Drawer is slid

out and then back in.

NO

Correct drive coupling.

2

2

nd

Drawer Lift-Up Motor rotation: the voltage

across PJ3A-13B on Master Board and GND is
DC0V (motor deenergized) and DC24V (motor

energized) after the 2

nd

Drawer has been slid

back in.

YES

Change motor.

NO

Change Master Board.

3

I/O check for 2

nd

Drawer Lift-Up Motor Pulse

Sensor operation: the voltage across PJ3A-
11B on Master Board and GND changes in the

range between DC0V and DC5V while 2

nd

Drawer Lift-Up Motor is turning.

YES

Change Master Board.

NO

Correct drive coupling.
Change sensor.

4

I/O check for 2

nd

Drawer Paper Lift-Up Sensor:

the voltage across PJ4A-12B on Master Board
and GND is DC0V (sensor unblocked) and
DC5V (sensor blocked).

YES

Change Master Board.

NO

Change sensor.

Step

Check

Result

Action

1

Lift-Up Motor turns when the 1

st

Drawer is slid

out and then back in.

NO

Correct drive coupling.

2

1

st

Drawer Lift-Up Motor rotation: the voltage

across PJ3A-13A on Master Board and GND is
DC0V (motor deenergized) and DC24V (motor

energized) after the 1

st

Drawer has been slid

back in.

YES

Change motor.

NO

Change Master Board.

3

I/O check for 1

st

Drawer Lift-Up Motor Pulse

Sensor operation: the voltage across PJ3A-
11A on Master Board and GND changes in the

range between DC0V and DC5V while 1

st

Drawer Lift-Up Motor is turning.

YES

Change Master Board.

NO

Correct drive coupling.
Change sensor.

4

I/O check for 1

st

Drawer Paper Lift-Up Sensor:

the voltage across PJ4A-6B on Master Board
and GND is DC0V (sensor unblocked) and
DC5V (sensor blocked).

YES

Change Master Board.

NO

Change sensor.

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments