Minolta DI450 Service Manual Download Page 144

Page: 144 / 271

S-3

1-2.

Explanation of the Touch Panel

(1)

Basis Screen

The Basic screen is the initial screen that appears when the copier is turned ON.

1. Supplementary Function Keys
• The auxiliary, Density, Orig.

Copy, and Basics keys are displayed.

2. Message Display
• Shows the current machine status, operating instructions and precautions, and other

data including the number of copies selected and the amount of paper still available for
use.

3. Basic Function/Key
• Shows the basic function keys and the corresponding functions currently selected for

use.

4. Set Function
• Shows graphic representations of the settings currently made for Orig.

Copy and Fin-

ishing.

5. Sub-message Display
• Shows what is being done with the currently reserved job.

4003P137CA

Summary of Contents for DI450
















































































































































































































































































Search results

Summary of Contents for DI450

Reviews:

Minolta DI450, Service Manual, Page: 144 / 271

Search results

Summary of Contents for DI450

Reviews: