manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 266 / 271

Share
Download
Minolta DI450 Service Manual Download Page 266

T-75

(6)

Black streaks or bands

(7)

Black spots

Section

Step

Check

Result

Action

Engine

1

PC Drum is dirty.

YES

Clean or change.

2

Cleaning Blade has correct
lateral movement.

NO

Correct lateral movement
mechanism.

3

Cleaning Blade is curled
upward or deteriorated.

YES

Change.

4

Comb Electrode and grid
mesh are dirty.

YES

Clean or change.

5

Upper Fusing Roller is dirty.

YES

Clean.

6

PH Unit window is dirty.

YES

Clean.

IR

1

Mirrors and lens are dirty.

YES

Clean.

2

Original Glass is dirty or
scratchy.

YES

Clean.

3

Exposure Lamp is dirty.

YES

Clean.

Section

Step

Check

Result

Action

Engine

1

PC Drum is dirty.

YES

Clean or change.

2

PC Drum Paper Separator
Fingers are dirty.

YES

Clean or change.

3

Toner spilled over areas inside
copier.

YES

Clean.

4

Upper Fusing Roller is dirty.

YES

Clean or change.

5

Toner is caked in the Develop-
ing Unit.

YES

Changer developer.

6

Main Erase Lamp is dirty.

YES

Clean.

IR

1

Mirrors and lens are dirty.

YES

Clean.

2

Original Glass is dirty or
scratchy.

YES

Clean or change.

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments