Minolta DI450 Service Manual Download Page 223

Page: 223 / 271

T-32

C0910

Drawer Paper Lift-Up

Sensor malfunction

• The 2

Drawer Paper Lift-Up Sensor is not blocked

(LOW) even after the lapse of 5 sec. after the 2

Drawer Paper Lift-Up Motor has started turning.

• The 2

Drawer Paper Lift-Up Sensor is not acti-

vated even when the 2

Drawer Paper Lift-Up

Motor Pulse Sensor detects 150 edges of rotation

detection pulses after the 2

Drawer Paper Lift-Up

Motor has started turning.

C0914

Drawer Lift-Up

Motor’s failure to turn

The 2

Drawer Paper Lift-Up Motor Pulse Sensor

detects no edges of rotation detection pulses even

after the lapse of 500 ms after the 2

Drawer Paper

Lift-Up Motor has started turning.

C0920

Drawer Paper Lift-Up

Sensor malfunction

• The 1

Drawer Paper Lift-Up Sensor is not blocked

(LOW) even after the lapse of 5 sec. after the 1

Drawer Paper Lift-Up Motor has started turning.

• The 1

Drawer Paper Lift-Up Sensor is not activated

even when the 1

Drawer Paper Lift-Up Motor Pulse

Sensor detects 150 edges of rotation detection

pulses after the 1

Drawer Paper Lift-Up Motor has

started turning.

C0924

Drawer Lift-Up

Motor’s failure to turn

The 1

Drawer Paper Lift-Up Motor Pulse Sensor

detects no edges of rotation detection pulses even

after the lapse of 500 ms after the 1

Drawer Paper

Lift-Up Motor has started turning.

C0950

Drawer Paper Lift-Up

Sensor malfunction

See the relevant option service manual.

C0954

Drawer Paper Lift-Up

Motor’s failure to turn

C0990

Main Tray lifting motion
failure

C0994

Main Tray Elevator
Motor’s failure to turn

C0996

Main Tray lock release
failure

C0997

Shift Gate malfunction

C0998

Shifter return failure

C099C Shift Motor’s failure to

turn

C09C0 LCT Elevator ascent/

descent failure

Code

Description

Detection Timing

Summary of Contents for DI450
















































































































































































































































































Search results

Summary of Contents for DI450

Reviews:

Minolta DI450, Service Manual, Page: 223 / 271

Search results

Summary of Contents for DI450

Reviews: