manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 204 / 271

Share
Download
Minolta DI450 Service Manual Download Page 204

T-13

Copier Paper Take-Up Misfeed Troubleshooting Procedures

• Paper is not taken up at all.

Step

Check

Result

Action

1

Paper meets product specifications.

NO

Change paper.

2

Paper is curled, wavy, or damp.

YES

Change paper.
Instruct user in correct
paper storage.

3

Edge Guide and Trailing Edge Stop are at cor-
rect position to accommodate paper.

NO

Set.

4

Paper Take-Up Roll is dirty with paper dust,
deformed, or worn.

YES

Clean or change.

5

Paper Lifting Plate is dirty or deformed.

YES

Clean or change.

6

Paper Separator Pad is dirty with paper dust,
deformed, or worn.

YES

Clean or change.

7

Paper take-up guide plate is dirty or deformed.

YES

Clean or change.

8

1

st

Drawer Paper Take-Up Motor turns when

the Start key is pressed with the 1

st

Drawer

selected.

NO

Correct drive coupling.
Change motor or Master
Board.

9

2

nd

Drawer Paper Take-Up Motor turns when

the Start key is pressed with the 2

nd

Drawer

selected.

NO

Correct drive coupling.
Change motor or Master
Board.

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments