manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 243 / 271

Share
Download
Minolta DI450 Service Manual Download Page 243

T-52

C0602

C0605

Step

Check

Result

Action

1

Scanner moves as moved manually.

NO

Correct drive coupling.
Rewind cables.

2

Connector on SCP Board is connected prop-
erly: PJ3IC on PWB-IC.

NO

Connect.

3

Scanner Motor turns when the Start key is
pressed.

NO

Correct drive coupling.
Change motor or SCP
Board.

4

Connector on Image Processing Board is con-
nected properly: PJ306B on PWB-B.

NO

Connect.

5

I/O check for Scanner Reference Position Sen-
sor

YES

Change Image Process-
ing Board.

NO

Correct actuator. Change
sensor.

Step

Check

Result

Action

1

Scanner moves as moved manually.

NO

Correct drive coupling.
Rewind cables.

2

Connector on Image Processing Board is con-
nected properly: PJ306B on PWB-B.

NO

Connect.

3

Light Blocking Plate is installed properly.

NO

Correct.

4

I/O check for Scanner Reference Position Sen-
sor

YES

Change Image Process-
ing Board.

NO

Correct actuator.
Change sensor.

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments