Minolta DI450 Service Manual Download Page 62

Page: 62 / 271

D-43

11. Remove the PC Drum Paper Fingers and AIDC Sensor Board as shown below.

NOTES

• At removal and reinstallation, use care not to damage the tip of the fingers.

Also, use care not to get hurt by the tip of the fingers.

• After reinstallation, perform the following adjustment procedure: Positioning of the PC

Drum Paper Separator Fingers.

☞

D-76

NOTE

When reinstalling the PC Drum Paper Separator Fin-
ger Holder Assy., fit the collar of the assy onto the cou-
pling holder in the rear.

1134D047AA

Coupling Holder

Collar

Assy

AIDC Sensor Board

4002D128AB

PC Drum Paper Separator Finger Installed

1156D063AA

Top View

Rear View

Hook the spring property.
After installation, check that the
Paper Separator Fingers operate
smoothly.

Summary of Contents for DI450
















































































































































































































































































Search results

Summary of Contents for DI450

Reviews:

Minolta DI450, Service Manual, Page: 62 / 271

Search results

Summary of Contents for DI450

Reviews: