manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 249 / 271

Share
Download
Minolta DI450 Service Manual Download Page 249

T-58

C0990

C0994

Step

Check

Result

Action

1

I/O check for 3

rd

Drawer Paper Lift-Up Sensor

operation: the voltage across PJ8A-2 on Con-
trol Board and GND is DC5V (sensor
unblocked) and DC0V (sensor blocked).

YES

Change Control Board.

NO

Change sensor.

2

I/O check for Lower Position Overrun Detecting
Sensor operation: the voltage across PJ7A-2A
on Control Board and GND is DC5V (sensor
unblocked) and DC0V (sensor blocked).

YES

Change Control Board.

NO

Change sensor or Cabinet
Transport Board.
Change flat cable.

3

I/O check for Elevator Lower Position Sensor
operation: the voltage across PJ7A-9A on Con-
trol Board and GND is DC5V (sensor
unblocked) and DC0V (sensor blocked).

YES

Change Control Board.

NO

Correct actuator. Change
sensor or Cabinet Trans-
port Board. Change flat
cable.

Step

Check

Result

Action

1

Elevator Motor turns when the Paper Descent
key is pressed.

NO

Correct drive coupling.

2

Elevator Motor rotation: the voltage across
PJ7A-6B (ascent)/PJ7A-7B (descent) on Con-
trol Board and GND is DC0V (motor deener-
gized) and DC24V (motor energized) when the
drawer is slid in or the Paper Descent key is
pressed.

YES

Change motor or Cabinet
Transport Board. Change
flat cable.

NO

Change Control Board.

3

I/O check for Elevator Motor Pulse Sensor
operation: the voltage across PJ7A-5A on Con-
trol Board and GND changes in the range
between DC0V and DC5V while the Elevator
Motor is turning.

YES

Change Control Board.

NO

Change gear or sensor.

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments