manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 268 / 271

Share
Download
Minolta DI450 Service Manual Download Page 268

T-77

(10) Smear on back

(11) Uneven image density

(12) Gradation reproduction failure

Section

Step

Check

Result

Action

Engine

1

Suction Belts are dirty.

YES

Clean.

2

Image Transfer Corona is dirty.

YES

Clean.

3

Image Transfer Guide Plate is
dirty.

NO

Clean.

4

Pre-Fusing Guide Plate is
dirty.

YES

Clean.

5

Fusing Rollers are dirty.

YES

Clean or change.

6

Toner spilled over area inside
copier.

YES

Clean.

Section

Step

Check

Result

Action

Engine

1

PC Drum is properly
grounded.

NO

Clean or change PC Drum
ground plate.

2

Comb Electrode and grid
mesh are dirty or deteriorated.

YES

Clean or change.

3

Image Transfer Corona is dirty
or deteriorated.

YES

Change.

4

Toner is even on Sleeve/Mag-
net Roller.

NO

Adjust DB. (See ADJUST-
MENT.) Correct developer
conveying mechanism.

IR

1

Mirrors and lens are dirty.

YES

Clean.

2

Exposure Lamp is dirty or
deteriorated.

YES

Clean or change.

Section

Step

Check

Result

Action

Engine

1

Wiring between PH Unit and
Image Processing Board is
connected.

YES

Change PH Unit.
Change Image Processing
Board.

IR

1

Shading sheet is dirty.

YES

Clean.

2

Wiring between CCD Assy
and Image Processing Board
is connected.

YES

Change CCD Assy.
Change Image Processing
Board.

NO

Connect.

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments