manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 240 / 271

Share
Download
Minolta DI450 Service Manual Download Page 240

T-49

C0500, C0510

Step

Check

Result

Action

1

Upper Fusing Roller Heater Lamp turns ON
when the Power Switch is turned ON.

YES

Correct thermistor for
mounting position and/or
clean.

2

Lower Fusing Roller Heater Lamp turns ON
when the malfunction is reset with the surface
temperature of Lower Fusing Roller Heater
Lamp is 140°C or less as indicated on “Level
History” under the Tech. Rep. mode.

NO

Check step 7 and onward.

3

Upper and Lower Fusing Roller Thermistors
are installed properly.

NO

Reinstall.

4

Upper and Lower Fusing Roller Thermistors
are dirty.

NO

Clean.

5

Upper Fusing Roller Thermistor operation: the
resistance across CN217-2 and 3 on the Fus-
ing Unit end is infinity with CN217 (4P) discon-
nected.

YES

Change Upper Fusing
Roller Thermistor.

6

Lower Fusing Roller Thermistor operation: the
resistance across CN218-2 and 3 on the Fus-
ing Unit end is infinity with CN218 (4P) discon-
nected.

YES

Change Lower Fusing
Roller Thermistor.

7

Upper Fusing Roller Thermostat and Upper
Fusing Roller Heater Lamp continuity: there is
continuity across CN11-1 and 8 with CN11
(16P) disconnected.

NO

Change thermostat and
heater lamp.

8

Lower Fusing Roller Heater Lamp continuity:
there is continuity across CN11-9 and 16 with
CN11 (16P) disconnected.

NO

Change heater lamp.

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments