Minolta DI450 Service Manual Download Page 134

Page: 134 / 271

D-115

(3)

Rewriting the ECC Board Data (option)

1. Unplug the power cord from the power outlet with the Power Switch OFF.
2. Remove the Rear Cover.

3. Insert the memory card into the ECC Board.

4002D538AB

4. Plug the power cord into the power outlet.
5. Turn ON the Power Switch.
6. This starts the rewriting sequence.

NOTE

D1 on the Master Board remains blinking while data is
being rewritten.

7. Check that D3 on the ECC Board turns ON.
8. If an LED other than D3 turns ON or if it takes

longer than 3 min. to rewrite the data, perform
steps 9 and 10, turn OFF the Power Switch, and
start the procedure over beginning with step 4.

4002D540AB

9. Unplug the power cord from the power outlet.

NOTE

At this time, do not turn OFF the Power Switch.

10. Remove the memory card.

4002D539AB

Summary of Contents for DI450
















































































































































































































































































Search results

Summary of Contents for DI450

Reviews:

Minolta DI450, Service Manual, Page: 134 / 271

Search results

Summary of Contents for DI450

Reviews: