Minolta DI450 Service Manual Download Page 177

Page: 177 / 271

S-36

(9)

Level History

• Displays the various level histories.

Touch Panel

Display

Setting

Date/Time Set

Set the date and time-of-day for Date Printing.

Common DT

Displays the screens for communications settings.

Dial Mode

Sets the type of telephone line of the user.

Auto Receive

Sets the auto reception function.

Touch Panel

Display

Setting

Fuser (Upper)

Displays the current value of the fusing temperature.

Fuser (Lower)

Displays the current value of the fusing temperature.

ATDC Set

Displays the voltage set with ATDC Sensor Automatic Adjustment
(F8).

ATDC Current

Displays the output voltage of the ATDC Sensor.

AIDC Fine Set

Displays the AIDC Sensor LED control voltage.

AIDC Coarse Set

Displays the load resistance level of the phototransistor used in the
AIDC Sensor.

AIDC Current

Displays the output voltage of the AIDC Sensor.

Vg Current

Displays the current value of the grid voltage.

Vb Current

Displays the current value of the developing bias voltage.

LD1

Displays the intensity value of LD1.

LD2

Displays the intensity value of LD2.

Tone

Pulse

YES

Summary of Contents for DI450
















































































































































































































































































Search results

Summary of Contents for DI450

Reviews:

Minolta DI450, Service Manual, Page: 177 / 271

Search results

Summary of Contents for DI450

Reviews: