Minolta DI450 Service Manual Download Page 59 | Manualshive

Page: 59 / 271

Minolta DI450 Service Manual Download Page 59

D-40

20. Mount the Scanner Motor Mounting Bracket Assy.
21. Remove the Cable Holding Jigs from the front and rear pulleys.
22. Remove the Allen wrench.
23. Mount the Scanner.
24. Reinstall the Left Cover, Right Cover, Rear Upper Cover and Control Panel.
25. Reinstall the Original Glass and EDH Glass.
26. Adjust the position of the Scanner and 2nd/3rd Mirrors Carriage.

☞

D-107

NOTE

Whenever the Scanner Drive Cables have been removed, be sure to carry out the following
check and adjustment: Orig. Size Adjust and Registration (CD).

18. Wind the hook end of the cable around pulley D

and pulley E.

4002D011AA

Pulley D

Pulley E

19. Fit the hook end of the cable into the groove in the

Cable Guide and hook the spring.

4002D120AB

Cable Guide

«
...
57
58
59
60
61
...
»

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments