manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 127 / 271

Share
Download
Minolta DI450 Service Manual Download Page 127

D-108

(5)

Adjustment of the 2nd/3rd Mirrors Carriage Assy for Parallel Alignment

Setting Instructions

If there is a gap between the 2nd/3rd Mirrors Carriage Assy and the Scanner Positioning
Jig at the front, turn the adjusting screw clockwise.
If there is a gap between the 2nd/3rd Mirrors Carriage Assy and the Scanner Positioning
Jig in the rear, turn the adjusting screw counterclockwise.

4. Lightly press the 2nd/3rd Mirrors Carriage Assy up against the Scanner Positioning Jig

and check that there is no clearance between the two.

5. Tighten one screw to secure the adjusting plate in position.

5. Press the Scanner and the 2nd/3rd Mirrors Car-

riage Assy tightly up against the Scanner Position-
ing Jigs.

6. Check that there is no clearance between the

Scanner and the Scanner Positioning Jig, and
between the 2nd/3rd Mirrors Carriage Assy and
the Scanner Positioning Jig.
If there is any clearance, adjust parallel alignment
of the 2nd/3rd Mirrors Carriage Assy after this
adjustment has been completed.

4002D508AA

7. Tighten the two Scanner Positioning Screws.

4002D237AB

1. Remove the Original Glass.
2. Loosen one screw that secures the adjusting plate.

4002D235AB

3. Turn the adjusting screw as necessary.

4002D236AA

Adjusting Screw

a

b

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments