manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 253 / 271

Share
Download
Minolta DI450 Service Manual Download Page 253

T-62

C0998

C099C

Step

Check

Result

Action

1

I/O check for Shifter Return Position Sensor
operation: the voltage across PJ7A-7A on Con-
trol Board and GND is DC5V (sensor
unblocked) and DC0V (sensor blocked).

YES

Change Control Board.

NO

Change sensor or Cabinet
Transport Board.
Change flat cable.

2

I/O check for Shifter Home Position Sensor
operation: the voltage across PJ7A-8A on Con-
trol Board and GND is DC5V (sensor
unblocked) and DC0V (sensor blocked).

YES

Change Control Board.

NO

Change sensor or Cabinet
Transport Board.
Change flat cable.

Step

Check

Result

Action

1

Shift Motor turns when the 3

rd

Drawer is slid in

with paper loaded on the Shift Tray (paper is
moved to the Main Tray).

NO

Correct drive coupling.

2

Shift Motor rotation: the voltage across PJ7A-
4B on Control Board and GND is DC0V (motor
deenergized) and DC24V (motor energized) in
step 1.

YES

Change motor or Cabinet
Transport Board.
Change flat cable.

NO

Change Control Board.

3

I/O check for Shift Motor Pulse Sensor opera-
tion: the voltage across PJ7A-3A on Control
Board and GND changes in the range between
DC0V and DC5V while the Shift Motor is turn-
ing.

YES

Change Control Board.

NO

Correct drive coupling.
Change sensor.

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments