Minolta DI450 Service Manual Download Page 159

Page: 159 / 271

S-18

4-3.

Tech. Rep. Mode Menu Function Tree

F1: Paper Passage
F2: HV Output
F5: AIDC Sensor
F8: ATDC Sensor
F12: Test Pattern

Opt. Mem. Check
Memory Check
Comp./Expansion

I.R.

Mem.

Prn.

Hard Disk Format
Hard Disk Check
ECC Check
Date/Time Check

→→

FLS Paper
Auto Paper Configuration
Function Limit
Touch Panel Adj.
Smoothing (Text)
Maintenance Call
Universal Tray

Toner Empty Stop
T/C Abnormal
Fusing (°C) Input
T/C Auto Recover

Controller Type
Main. Sw notice
Printer Time-out
Warning Level
Peripheral Mode

Change Fixed Zoom
Paper Size Input
Marketing Area
Orig. Size Option
Tel. # Input
Hard Disk

Paper
Maintenance
Jam
PM
Consumables
Trouble

Tech. Rep. Mode

Function

Tech. Rep.
Choice

System Input

Counter

Printer

Image
Memory

System Set

Printer

Controller
Set

Summary of Contents for DI450
















































































































































































































































































Search results

Summary of Contents for DI450

Reviews:

Minolta DI450, Service Manual, Page: 159 / 271

Search results

Summary of Contents for DI450

Reviews: