Minolta DI450 Service Manual Download Page 57

Page: 57 / 271

D-38

7. Wind the hook end of the cable around the pulley

five turns counterclockwise, from the rear toward
the front side.

NOTE

Make sure that no part of the cable rides on the other.

4002D007AA

8. Slip the Cable Holding Jig onto the pulley to secure

the cable in position.

4002D502AA

9. Mount the front and rear pulleys and bushings on

the shaft and install the shaft to the IR Unit.

10. Mount the Scanner Drive Gear on the shaft and

secure it in position with one screw.

4002D115AD

11. Install an Allen wrench into the holes in the shaft

and the IR Base Plate.

4002D116AD

12. Slide the front pulley and bushing to the front and

install one mounting screw.

4002D117AC

Summary of Contents for DI450
















































































































































































































































































Search results

Summary of Contents for DI450

Reviews:

Minolta DI450, Service Manual, Page: 57 / 271

Search results

Summary of Contents for DI450

Reviews: