Minolta DI450 Service Manual Download Page 128

Page: 128 / 271

D-109

(6)

Adjustment of the Gap Between the Doctor Blade and Sleeve Roller

(D.B. Adjustment)

Requirement

The gap between the Doctor Blade and Sleeve Roller should be 0.6 + 0.03 - 0.05 mm.

Adjustment Procedure

1. Slide out the Developer Unit and remove the PC

Drum Charge Corona and PC Drum.

2. Remove two screws and the Developer Scattering

Prevention Plate.

4002D224AA

3. Using a brush, whisk developer off the surface of

the Sleeve Roller.

4002D225AA

4. Install the Sleeve/Magnet Roller Positioning Jig into

the Developer Unit.

1136D051AA

5. Loosen three screws that secure the Doctor Blade.

Insert the D.B. Adjusting Jigs between the Doctor
Blade and Sleeve Roller.

6. Press down the Doctor Blade until it positively con-

tacts the D.B. Adjusting Jigs. Then, tighten the
three screws to secure the Doctor Blade.

4002D226AA

Summary of Contents for DI450
















































































































































































































































































Search results

Summary of Contents for DI450

Reviews:

Minolta DI450, Service Manual, Page: 128 / 271

Search results

Summary of Contents for DI450

Reviews: