manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 83 / 271

Share
Download
Minolta DI450 Service Manual Download Page 83

D-64

(12) Removal of the Web Roller

(13) Removal of the Web Pressure Roller

1. Remove the Web Roller Assy.
2. Remove two screws and the Web Roller bushing

and Web Take-Up Roller bushing.

NOTE

When reinstalling the Web Roller bushing and Web
Take-Up Roller bushing, ensure that they are in correct
position without being tilted or out of position.

4002D189AA

3. Remove the Web Roller and Web Take-Up Roller.

NOTES

• When reinstalling the Web Roller and Web Take-Up

Roller, wind the web around the Web Take-Up Roller
at least one complete turn. Make also sure that the
web is not slack off.

• When the Web Roller has been removed, clear

Web-Count of Consumables Counter available from
Tech. Rep. mode.

4002D190AB

1. Remove the Web Roller Assy.
2. Remove the Web Roller and Web Take-Up Roller.
3. Remove the springs at the front and rear.

4002D191AB

4. Remove the E-rings and bushings from the front

and rear end and remove the Web Pressure Roller.

4002D192AC

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments