manualshive.com logo in svg

Minolta DI450, Service Manual, Page: 260 / 271

Share
Download
Minolta DI450 Service Manual Download Page 260

T-69

(22) Copier does not turn ON.

• Main Relay does not turn ON.

Relevant Electrical Parts

Power Switch (S1)
Front Door Interlock Switch (S21)
Upper Left Door Interlock Switch (S22)
Main Relay (RY1)

DC Power Supply Main (PU1)
DC Power Supply Sub (PU2)
Power Supply Board (PWB-C)
Master Board (PWB-A)

Step

Check

Result

Action

1

Power supply voltage check: there is a rated
AC voltage supply across CN1PU1-1 and 3 of
DC Power Supply Main and across PJ1PU2-1
and 3 of DC Power Supply Sub when the
power cord is plugged in the power outlet.

NO

Check wall power outlet
voltage. Check power cord
for continuity. Check har-
ness between DC Power
Supply Main and Sub for
continuity.

2

DC Power Supply Sub operation: the voltage
across PJ2PU2-1 and 2 of DC Power Supply
Sub is DC5V when the power cord is plugged
in the power outlet.

NO

Change DC Power Supply
Sub.

3

DC Power Supply Main operation: the voltage
across PJ12PU1-1 and 5 of DC Power Supply
Main is DC5V and the voltage across
PJ12PU1-2 and 5 of DC Power Supply Main is
DC5V when the Power Switch is turned ON.

NO

Check harness.

4

DC Power Supply Main operation: the voltage
across PJ12PU1-2 and 5 of DC Power Supply
Main is DC0.5V to 1.0V when the Power Switch
is turned ON.

NO

Check harness.

YES

Change DC Power Supply
Main.

5

Power Switch operation: the voltage across
PJ15A-3 on Master Board and GND is DC5V
(switch OFF) and DC0V (switch ON).

NO

Check and change, as
necessary, Power Switch.

6

Front Door Interlock Switch operation: the volt-
age across PJ6C-1 on Power Supply Board
and GND is DC0V (Power Switch OFF) and
DC24V (Power Switch ON).

NO

Check harness.
Change Power Supply
Board.

7

Upper Left Door Interlock Switch operation: the
voltage across PJ6A-2 on Master Board and
GND is DC5V when the Upper Left Door is
open.

NO

Check harness.
Change Master Board.

8

Front Door Interlock Switch and Upper Left
Door Interlock Switch operation: the voltage
across PJ6C-2 on Power Supply Board and
GND is DC24V when both doors are closed.

NO

Readjust the position of,
check, or change Front
Door Interlock Switch.
Check and change, as
necessary, Upper Left
Door Interlock Switch.

Summary of Contents for DI450
















































































































































































































































































Reviews:

No comments