3. Synth Parameters
93
Reverse
Play from the last step (the step number specified by
“Last Step”) in reverse.
Alt1/Alt2
Alternately play in Forward and Reverse directions. Alt
1 immediately changes direction at the end points, so the
first step and last steps are played only once per loop.
Alt 2 plays the first step and the last step on both the way
up and on the way down, so these steps will be played
twice per loop.
Playback is always in the Forward direction for
Motion Rec.
3: RunMode
[OneShot, Loop]
Specifies the loop setting for playback.
OneShot
The sequence will play for only one cycle, and will main-
tain the value of the last step.
Loop
The sequence will play as a loop, using the sequence
type specified by “Seq Type.”
When you're using the Motion Rec function, or
“KeySync” is off, playback is always in the Loop
mode.
4: KeySync
[Off, Timbre, Voice]
Specifies how the sequence will be reset when note-on
occurs (i.e., when a key is played).
Off
The sequence will not be reset when note-on occurs.
Timbre
The sequence will be reset when the first note-on occurs
for a timbre from a condition of all keys being released.
In the case of a program for which different regions of
the keyboard play different timbres (i.e., a split pro-
gram), the reset will occur for the timbre that was played
by the note-on.
Voice
The sequence will be individually reset by each new
note-on that occurs.
If both the modulation sequencer and the arpeg-
giator are on, you should set this parameter to Off
or Timbre. If this is set to Voice, the sequence will
be reset each time the arpeggiator generates a
note. If you set this to Timbre, the sequence will be
reset each time a chord change occurs.
5: Resolutn (Resolution)
[
3
1/48…
1/1]
Specifies the playback speed of the sequence relative to
the tempo (MIDI clock) specified by the [TEMPO] knob.
The sequence will advance by one step for each note val-
ue you specify here, relative to the tempo. For example
if you set this to
1/4, the sequence will advance one
step for each quarter note.
P12–2…4: SEQ1…SEQ3
1: Knob
[None, Pitch…Pch6Int]
Selects the parameter that will be recorded in the modu-
lation sequencer.
None
The modulation sequence will do nothing.
Pitch
The modulation sequence will modify the overall pitch
of the sounding oscillators over a range of ±24 semi-
tones.
Other
The modulation sequence will modify the parameter as-
signed to a specific panel knob over a range of ±63 (±24
for OSC2 Sem).
If the same parameter is assigned to more than one
sequence, an “*” is shown at the right. In this case,
assignments will take priority in the order of
SEQ3, SEQ2, and SEQ1.
2: Motion
[
,
]
Specifies how the recorded values will change when the
sequence is played.
(Smooth)
The change will be continuous, with the values recorded
at each step connected by straight lines.
Step
16
Step
15
Step
14
Step
03
Step
02
Step
01
Reverse (Last Step=16)
Run Mode=Loop
Alt1 (Last Step=16)
Alt2 (Last Step=16)
Step
01
Step
02
Step
15
Step
16
Step
01
Step
02
Step
15
Step
16
Step
01
Step
02
Step
15
Step
16
Step
01
Step
02
Step
15
Run Mode
=Loop
Run Mode
=Loop
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Steps
Summary of Contents for MMT RADIAS
