Korg MMT RADIAS Owner'S Manual Download Page 19

Page: 19 / 176

Front panel

[LO] knob

Adjusts the level of the low frequency range. Turning
this toward the right will boost the level of the low fre-
quency range, and turning it toward the left will de-
crease the level of the low frequency range.
You can specify the center frequency of the low frequen-
cy range in the Program Edit mode P13–1: EQ/FX – EQ
tab page.

18. INSERT FX

[FX1-FX2] button

Selects which insert effect is available for editing. FX1
parameters is selected when this button is dark, and FX2
is selected when this button is lit.

[ON] button

Turns the insert effect selected by [FX1-FX2] on/off.
When this button is lit, the effect is on and will be ap-
plied.

[EDIT1], [EDIT2] knobs

These knobs adjust various effect parameters.
They will adjust the effect selected by the [FX1-FX2] but-
ton. The parameter being adjusted will depend on the
type of effect selected.

19. MASTER FX

[ON] button

Switches the master effect on/off. When this button is
lit, the effect is on.

[EDIT] knob

Adjusts various master effect parameters. The parame-
ter being adjusted will depend on the effect type you’re
using.

20. ARPEGGIATOR/STEP SEQUENCER

[ON] button

This turns the arpeggiator and step sequencers on/off.
The arpeggiator and step sequencers are all turned on
together

[LATCH] button

This button turns on and off the Latch function that af-
fects the arpeggiator and the step sequencers.
When this function is on (lit), the arpeggiator and/or
step sequencers will continue playing even after you
take your hand off the keyboard.
The latch setting can be set independently for the arpeg-
giator and each step sequencer.

[TYPE/STEP REC] button

The function of this button depends on the setting of the
[SELECT] button, which can be set to ARPEGGIATOR,
STEP SEQ 1, or STEP SEQ 2. If ARPEGGIATOR is select-
ed, pressing this button will scroll through the different
arpeggiator types.
If STEP SEQ 1 or 2 is selected, then this button will act as
the recording button for that step sequencer. Press this

button to enter record-ready mode; recording will begin
when you play the keyboard etc.

[SELECT] button

Selects the arpeggiator or the step sequencer that will be
assigned to play the timbre.

[GATE] knob

Adjusts the gate time (duration) specified for each step
of the arpeggiator or step sequencer.

[TEMPO] knob

Adjusts the playback tempo of the arpeggiator or step
sequencer. This setting will also affect other parameters
that are tied to the internal tempo, such as playback
speed of a modulation sequencer, an LFO rate, or an ef-
fect delay rate.

[TAP TEMPO REST/TIE] button

During playback, you can enter a tempo manually by
lightly tapping this button a few times at the desired
tempo (Tap Tempo). When you’re recording using the
step sequencer, this button allows you to enter ties and
rests.

TEMPO LED

This will blink at quarter note intervals of the current
tempo.

21. EG1 (FILTER)/EG2 (AMP)

[ATTACK] knob

Adjusts the attack time (rise time from the key on).

[DECAY] knob

Adjusts the decay time (the time from the end of the at-
tack time until the sustain level is reached).

[SUSTAIN] knob

Adjusts the sustain level (the level at which the sound is
held).

[RELEASE] knob

Adjusts the release time (the time it takes the sound to
completely stop after you release the key).

22. PORTAMENTO