Korg MMT RADIAS, Owner'S Manual, Page: 140 / 176

Effect guide
134
16. St.AutoPanDly
(Stereo Auto Panning Delay)
This is a stereo delay that uses an LFO to pan the delay
sound between left and right.
Dry/Wet [Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
TempoSync (DelayTime Tempo Sync) [Off, On]
☞
p.132 LCR Delay “TempoSync (DelayTime Tempo
Sync)”
Time Ratio [TempoSync Off: 000.5…400.0% (OVER)/
TempoSync On: 012.5…400.0% (OVER)]
☞
p.132 LCR Delay “Time Ratio”
L Delay, R Delay (L, R Delay Time)
[IFX: 000…500msec, MFX: 000…700msec, 1/64… 1/1]
☞
p.132 StDelay “L Delay, R Delay (L, R Delay Time)”
Feedback [000…127]
☞
p.132 StDelay “Feedback”
Mod Depth [000…127]
Sets the depth of modulation.
TempoSync (LFO Tempo Sync) [Off, On]
Specifies whether the LFO cycle will be synchronized
with the tempo specified by the [TEMPO] knob or MIDI
clock.
☞
p.125 “TempoSync (LFO Tempo Sync)”
LFO Freq (LFO Frequency) [0.01…100.0Hz]
Sets the LFO speed.
☞
p.125 “LFO Freq (LFO Frequency)”
Sync Note (LFO Sync Note) [8/1…1/64]
Sets the LFO frequency as a proportion of the tempo set
by the [TEMPO] knob. This parameter will be displayed
and can be set if “TempoSync” is On.
☞
p.125 “Sync Note (LFO Sync Note)”
LFO Wave (LFO Waveform) [Saw, Squ, Tri, Sin, S&H]
Selects the LFO waveform.
☞
p.125 “LFO Wave (LFO Waveform)”
LFO Shape [–63…+63]
☞
p.125 “LFO Shape”
Key Sync (LFO KeySync) [Off, Timbre]
Specifies whether the LFO will be reset by note-on.
☞
p.125 “Key Sync (LFO KeySync)”
InitPhase (LFO Init Phase) [000…180°]
Sets the starting location of the waveform. This parame-
ter will be displayed and can be set if “KeySync” is Tim-
bre.
☞
p.125 “InitPhase (LFO Init Phase)”
LFO Spread [–180…+180°]
Sets the phase difference between the left and right
channels.
High Damp [000…100%]
Sets the damping amount in the high range.
Low Damp [000…100%]
Sets the damping amount in the low range.
Trim [000…127]
Sets the input level.
17. Mod Delay (Modulation Delay)
This stereo delay uses an LFO to sweep the delay time.
The pitch also varies. You will obtain a delay sound with
swell and shimmering. You can also control the delay
time using a modulation source.
Dry/Wet [Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
TempoSync (DelayTime Tempo Sync) [Off, On]
☞
p.132 LCR Delay “TempoSync (DelayTime Tempo
Sync)”
Time Ratio [TempoSync Off: 000.5…400.0% (OVER)
/TempoSync On: 012.5…400.0% (OVER)]
☞
p.132 LCR Delay “Time Ratio”
L Delay, R Delay (L, R Delay Time)
[IFX: 000…980msec, MFX: 0000…1380msec,
1/64… 1/1]
☞
p.132 StDelay “L Delay, R Delay (L, R Delay Time)”
Feedback [000…127]
Sets the feedback amount for the left channel.
Mod Depth [000…127]
Sets the depth of LFO modulation.
Left
Right
Dry / Wet
Dry / Wet
Stereo In - Stereo Out
LFO Spread
LFO Shape
Pan
Pan
LFO
Depth
Delay
Delay
High Damp Low Damp
High Damp Low Damp
Feedback
Trim
Trim
Left
Right
Feedback
LFO Spread
Dry / Wet
Dry / Wet
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Delay
LFO
+