Effect parameters
131
SmthHall
only MFX
Hall-type reverb, producing the reverberation of a larg-
er hall or stadium. The reverberation features a smooth
release.
Selectable only for the master effect.
Plate
only IFX
Plate reverb.
Selectable only for an insert effect.
WetPlate
only MFX
Plate reverb that produces warm, dense reverberation.
Selectable only for the master effect.
DryPlate
only MFX
Plate reverb with a dry, light feel.
Selectable only for the master effect.
Room
Room-type reverb with a tight feeling, and emphasis on
the early reflections. By changing the balance between
the early reflections and the reverberation, you can sim-
ulate different types of wall material.
BritRoom
only MFX
Room-type reverb with a bright feeling, and emphasis
on the early reflections. (
☞
Reverb Room)
Selectable only for the master effect.
Rev Time (Reverb Time)
[00.1…10.0sec]
Sets the reverberation time.
The selectable range of reverb time will depend on the
“Type” setting.
Hall–DryPlate: 0.1–10sec
Room, BritRoom: 0.1–3.0sec
High Damp
[000…100%]
Sets the damping amount in the high range.
Pre Delay
only MFX
[000…200msec]
Sets the delay time from the dry sound.
PrDlyThru (Pre Delay Thru)
only MFX
[000…127]
Sets the mix ratio of non-delay sound.
Trim (Pre EQ Trim)
only MFX
[000…127]
Sets the EQ input level.
LoEQGain (Low EQ Gain)
only MFX
[–15.0…+15.0dB]
Sets the gain of Low EQ.
HiEQGain (High EQ Gain)
only MFX
[–15.0…+15.0dB]
Sets the gain of High EQ.
ER Level
only MFX
[000…127]
Sets the time taken from the original sound to the first
early reflection.
When used for the master effect, this is displayed and
can be set only if Room or BritRoom is selected.
Rev Level (Reverb Level)
only MFX
[000…127]
Sets the reverberation level.
This is displayed and can be set only if Room or Brit-
Room is selected for the master effect.
12. Early Reflect (Early Reflections)
This effect is only the early reflection part of a reverber-
ation sound, and adds presence to the sound. You can
select one of the four decay curves.
Dry/Wet
[Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
Type
[Sharp, Loose, Modulation, Reverse]
Selects the decay curve for the early reflection.
ER Time
[IFX: 010…400msec/MFX: 010…800msec]
Sets the time length of early reflection.
The range is 10–400 msec when used for an insert effect,
or 10–800 msec when used for the master effect.
Pre Delay
[IFX: 000…100msec/MFX: 000…200msec]
Sets the time taken from the original sound to the first
early reflection.
The range is 0–100 msec when used for an insert effect,
or 0–200 msec when used for the master effect.
Trim (Pre EQ Trim)
[000…127]
Sets the input level of EQ applied to the effect sound.
LoEQGain (Low EQ Gain)
only MFX
[–15.0…+15.0dB]
Sets the gain of Low EQ.
HiEQGain (High EQ Gain)
only MFX
[–15.0…+15.0dB]
Sets the gain of High EQ.
High Damp
only IFX
[000…100%]
Sets the damping amount in the high range.
Low Damp
only IFX
[000…100%]
Sets the damping amount in the low range.
Left
Right
Dry / Wet
Dry / Wet
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
EQ Trim
+
EQ Trim
Pre Delay
Early Reflections
IFX: Low Damp
MFX: LEQ
IFX: High Damp
MFX: HEQ
Sharp
Loose
Modulated
Early Reflections - Type
Reverse
Dry
Pre Delay
ER Time
Summary of Contents for MMT RADIAS
