Korg MMT RADIAS, Owner'S Manual, Page: 138 / 176

Effect guide
132
13. L/C/R Delay
This multitap delay outputs three Tap signals to the left,
center, and right respectively. You can also adjust the
left and right spread of the delay sound.
Dry/Wet [Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
TempoSync (DelayTime Tempo Sync) [Off, On]
Specifies whether the delay time will be synchronized.
If this is On, the delay time will synchronize to the tem-
po or MIDI clock.
Time Ratio [TempoSync Off: 000.5…400.0% (OVER)
/TempoSync On: 012.5…400.0% (OVER)]
Sets each delay time as a proportion relative to the “L
Delay,” “C Delay,” and “R Delay” values. The available
range will depend on whether “TempoSync” is On or
Off.
For example if “Time Ratio” is 50%, “L Delay” is 500
msec, “C Delay” is 1000 msec, and “R Delay” is 1200
msec, the delay times will be 250 msec, 500 msec, and
600 msec respectively.
If you use this effect and a delay or chorus effect as
the two insert effects, the delay times will be limit-
ed.
If the delay times in conjunction with the “Time
Ratio” setting exceed the limit, “Time Ratio” will
indicate OVER.
L Delay, C Delay, R Delay (L, C, R Delay Time)
[IFX: 0000…1000msec, MFX: 0000…1400msec,
1/64… 1/1]
These set the L, C, and R delay times.
The delay time is determined by these settings and the
“Time Ratio” value.
If “TempoSync” is Off, these delay times are set in msec
units. The range is 0–1000 msec for an insert effect, or 0–
1400 for a master effect.
If “TempoSync” is On, these delay times are set as a tim-
ing resolution relative to the tempo specified by the
[TEMPO] knob or MIDI clock.
L Level, C Level, R Level (L, C, R Delay Level) [000…127]
These adjust the output level of the L, C, and R delays.
C Fback (C Feedback) [000…127]
Sets the feedback amount of TapC.
High Damp [000…100%]
Sets the damping amount in the high range.
Low Damp [000…100%]
Sets the damping amount in the low range.
Trim [000…127]
Sets the input level.
Spread [000…127]
Sets the width of the stereo image of the effect sound.
The stereo image is widest with a value of 127, and the
effect sound of both channels is output from the center
with a value of 0.
14. St.Delay (Stereo Delay)
This is a stereo delay, and can by used as a cross-feed-
back delay effect in which the delay sounds cross over
between the left and right by changing the feedback
routing.
Dry/Wet [Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
Type [Stereo, Cross]
Selects the delay type.
With the Stereo setting, this will be a conventional stereo
delay.
With the Cross setting, this will be a cross-feedback de-
lay in which the delay sound bounces between left and
right.
TempoSync (DelayTime Tempo Sync) [Off, On]
Specifies whether the delay tempo will be synchronized.
☞
p.132 LCR Delay “TempoSync (DelayTime Tempo
Sync)”
Time Ratio [TempoSync Off: 000.5…400.0% (OVER)
/TempoSync On: 012.5…400.0% (OVER)]
☞
p.132 LCR Delay “Time Ratio”
L Delay, R Delay (L, R Delay Time)
[IFX: 000…500msec, MFX: 000…700msec, 1/64… 1/1]
These set the left and right channel delay times.
If “TempoSync” is Off, these delay times are set in msec
units. The range is 0–500 msec for an insert effect, or 0–
700 for a master effect.
If “TempoSync” is On, these delay times are set as a tim-
ing resolution relative to the tempo specified by the
[TEMPO] knob or MIDI clock.
Feedback [000…127]
Sets the amount of feedback for the left and right chan-
nels.
C Delay
R Delay
Left
Right
Feedback
Spread
Dry / Wet
Dry / Wet
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Trim
High Damp Low Damp
L Delay
Trim
+
Level
Level
Level
Delay
Delay
Stereo/Cross
Left
Right
Feedback
Dry / Wet
Dry / Wet
Stereo In - Stereo Out
Trim
Trim
High Damp Low Damp
High Damp Low Damp
Spread
Stereo/Cross