Korg MMT RADIAS, Owner'S Manual, Page: 141 / 176

Effect parameters
135
LFO Freq (LFO Frequency) [0.01…100.0Hz]
Sets the LFO speed. Increasing this value will result in a
faster frequency.
LFOSpread [–180…180°]
Sets the phase difference between the left and right
channels.
18. St.Mod Delay
(Stereo Modulation Delay)
This is a stereo modulation delay.
Dry/Wet [Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
TempoSync (DelayTime Tempo Sync) [Off, On]
☞
p.132 LCR Delay “TempoSync (DelayTime Tempo
Sync)”
Time Ratio [TempoSync Off: 000.5…400.0% (OVER)
/TempoSync On: 012.5…400.0% (OVER)]
☞
p.132 LCR Delay “Time Ratio”
L Delay, R Delay (L, R Delay Time)
[IFX: 000…480msec, MFX: 000…680msec, 1/64… 1/1]
☞
p.132 StDelay “L Delay, R Delay (L, R Delay Time)”
Feedback [000…127]
☞
p.132 StDelay “Feedback”
Mod Depth [000…127]
Sets the depth of LFO modulation.
LFO Freq (LFO Frequency) [0.01…100.0Hz]
Sets the LFO speed. Increasing this value will result in a
faster frequency.
LFOSpread [–180…180°]
Sets the phase difference between the left and right
channels.
19. Tape Echo
This effect simulates a tape echo unit. The distortion and
tonal change typical of magnetic tape are also repro-
duced.
Dry/Wet [Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
TempoSync (DelayTime Tempo Sync) [Off, On]
☞
p.132 LCR Delay “TempoSync (DelayTime Tempo
Sync)”
Time Ratio [TempoSync Off: 000.5…400.0% (OVER)
/TempoSync On: 012.5…400.0% (OVER)]
☞
p.132 LCR Delay “Time Ratio”
Tap1Delay, Tap2 Delay(Tap1, Tap2 Delay Time)
[IFX: 000…980msec, MFX: 0000…1380msec,
1/64… 1/1]
Sets the delay times for Tap1 and Tap2.
☞
p.132 LCR Delay “L Delay, C Delay, R Delay (L, C, R
Delay Time)”
Tap1Level, Tap2 Level [000…127]
Sets the Tap1 output level and Tap2 output level.
Feedback [000…127]
Sets the Tap1 feedback amount.
High Damp [000…100%]
Sets the damping amount in the high range.
Low Damp [000…100%]
Sets the damping amount in the low range.
Trim [000…127]
Sets the input level.
Saturatn (Saturation) [000…127]
Sets the distortion amount.
Wah Freq (Wah Flutter Frequency) [0.01…100.0Hz]
Sets the frequency at which pitch variation will occur in
Hz stepsl.
Wah Depth (Wah Flutter Depth) [000…127]
Sets the depth of pitch variation.
Pre Tone [000…127]
Sets the tone of the input.
Left
Right
Feedback
LFO Spread
Dry / Wet
Dry / Wet
Stereo In - Stereo Out
Delay
Delay
LFO
Wah Flutter
Tap2 Level
+
Tape
Saturation
Left
Right
Dry / Wet
Trim
Tape1 Level
Dry / Wet
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Feedback
High / Low Damp Pre Tone
Delay
Spread