Korg MMT RADIAS, Owner'S Manual, Page: 139 / 176

Effect parameters
133
The amount of feedback for the right channel is linked
with the proportion of the left and right delay times so
that the decay times of the left and right channels will
stay the same.
High Damp [000…100%]
Sets the damping amount in the high range.
Low Damp [000…100%]
Sets the damping amount in the low range.
Trim [000…127]
Sets the input level.
Spread [000…127]
Sets the width of the stereo image of the effect sound.
☞
p.132 LCR Delay “Spread”
15. AutoPanDelay
(Auto Panning Delay)
This stereo delay effect pans the delay sound left and
right using the LFO.
Dry/Wet [Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
TempoSync (DelayTime Tempo Sync) [Off, On]
☞
p.132 LCR Delay “TempoSync (DelayTime Tempo
Sync)”
Time Ratio [TempoSync Off: 000.5…400.0% (OVER)
/TempoSync On: 012.5…400.0% (OVER)]
☞
p.132 LCR Delay “Time Ratio”
L Delay, R Delay (L, R Delay Time)
[IFX: 0000…1000msec, MFX: 0000…1400msec,
1/64… 1/1]
These set the left and right channel delay times.
If “TempoSync” is Off, these delay times are set in msec
units. The range is 0–1000 msec for an insert effect, or 0–
1400 for a master effect.
If “TempoSync” is On, these delay times are set as a tim-
ing resolution relative to the tempo specified by the
[TEMPO] knob or MIDI clock.
Feedback [000…127]
Sets the feedback amount for the left channel.
Mod Depth [000…127]
Sets the depth of modulation.
TempoSync (LFO Tempo Sync) [Off, On]
Specifies whether the LFO cycle will be synchronized
with the tempo specified by the [TEMPO] knob or MIDI
clock.
☞
p.125 “TempoSync (LFO Tempo Sync)”
LFO Freq (LFO Frequency) [0.01…100.0Hz]
Sets the LFO speed.
☞
p.125 “LFO Freq (LFO Frequency)”
Sync Note (LFO Sync Note) [8/1…1/64]
Sets the LFO frequency as a proportion of the tempo set
by the [TEMPO] knob. This parameter will be displayed
and can be set if “TempoSync” is On.
☞
p.125 “Sync Note (LFO Sync Note)”
LFO Wave (LFO Waveform) [Saw, Squ, Tri, Sin, S&H]
Selects the LFO waveform.
☞
p.125 “LFO Wave (LFO Waveform)”
LFO Shape [–63…+63]
☞
p.125 “LFO Shape”
Key Sync (LFO KeySync) [Off, Timbre]
Specifies whether the LFO will be reset by note-on.
☞
p.125 “Key Sync (LFO KeySync)”
InitPhase (LFO Init Phase) [000…180°]
Sets the starting location of the waveform. This parame-
ter will be displayed and can be set if “Key Sync” is Tim-
bre.
☞
p.125 “InitPhase (LFO Init Phase)”
High Damp [000…100%]
Sets the damping amount in the high range.
Low Damp [000…100%]
Sets the damping amount in the low range.
Trim [000…127]
Sets the input level.
Left
Right
Dry / Wet
Dry / Wet
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
LFO Spread
LFO Shape
Pan
LFO
Depth
Delay
High Damp Low Damp
Feedback
Trim
Trim
+