Korg MMT RADIAS, Owner'S Manual, Page: 146 / 176

Effect guide
140
Mode [Slow, Medium, Fast]
This parameter selects the pitch shifter operating mode.
With Slow, tonal quality will not be changed too much.
With Fast, the effect becomes a Pitch Shifter that has a
quick response, but may change the tone. Medium is in
between these two. If you do not need to set too much
pitch shift amount, set this parameter to Slow. If you
wish to change the pitch significantly, use Fast.
High Damp [000…100%]
Sets the damping amount in the high range.
Trim [000…127]
Sets the input level.
27. Grain Shifter (IFX)
/St.GrainShift (MFX)
This effect samples extremely brief fragments of the
sound at a specified interval, and plays them as a loop.
This is effective when used on external input sounds
that are constantly changing.
If used for an insert effect, this will be mono-in/mono-
out.
If used for the master effect, this will be stereo-in/ste-
reo-out.
Dry/Wet [Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
Tempo Sync (Duration Tempo Sync) [Off, On]
Specifies whether playback of the looped waveform will
be synchronized.
If this is On, the looped waveform will play in synchro-
nization with the tempo or MIDI clock.
Time Ratio [TempoSync Off: 000.5…400% (OVER)/
[TempoSync On: 012.5…400% (OVER)]
This specifies the length of the looped waveform rela-
tive to the “Duration” value.
Duration
[IFX: 000…500msec, MFX: 000…350msec, 1/64… 1/1]
Sets the duration of the grain.
The length of the waveform is determined by this setting
and the “TimeRatio” setting.
If “TempoSync” is Off, this is set in msec units. The
range is 0–500 msec for an insert effect, or 0–350 for a
master effect.
If “TempoSync” is On, this is set as a timing resolution
relative to the tempo specified by the [TEMPO] knob or
MIDI clock.
If you use this in an insert effect and the other in-
sert effect uses a delay or chorus effect, the wave-
form length will be limited.
If the “Duration” and “TimeRatio” settings exceed
the limit, an indication of OVER will appear for
the “TimeRatio.”
TempoSync (LFO Tempo Sync) [Off, On]
Specifies whether the LFO cycle will be synchronized
with the tempo specified by the [TEMPO] knob or MIDI
clock.
☞
p.125 “TempoSync (LFO Tempo Sync)”
LFO Freq (LFO Frequency) [0.01…100.0Hz]
If “TempoSync” is Off, this specifies the cycle at which
the waveform is switched in Hz units
The waveform length specified by “Duration” will play
as a loop, and the waveform will switch at each cycle of
the LFO.
If this parameter is assigned to “Edit1,” “Edit2,” or
“Edit,” turning “TempoSync” On will switch the
assignment to Sync Note.
Sync Note (LFO Sync Note) [8/1…1/64]
Sets the LFO frequency as a proportion of the tempo set
by the [TEMPO] knob. This parameter will be displayed
and can be set if “TempoSync” is On.
☞
p.125 “Sync Note (LFO Sync Note)”
Key Sync (LFO KeySync) [Off, Timbre]
Specifies whether the LFO will be reset by note-on.
☞
p.125 “Key Sync (LFO KeySync)”
+
Left
Right
Sample Cycle
Dry / Wet
Dry / Wet
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
LFO
Grain Shifter
Left
Right
Sample Cycle
LFO Spread
Sample Cycle
Dry / Wet
Dry / Wet
Stereo In - Stereo Out
LFO
Grain Shifter
Grain Shifter
In
Out
LFO Cycle /Duration
LFO Cycle
Duration