Effect parameters
123
Effect parameters
• [parameter name]
only MFX
:
This parameter will be
displayed and can be set only when the effect is
used by a master effect.
• [parameter name]
only IFX
:
This parameter will be
displayed and can be set only when the effect is
used by an insert effect.
• [effect name]
double size
:
This effect can be selected
only for insert effect 1. If you select this type of
effect, you can’t use insert effect 2.
• [parameter name]
:
This parameter can be
assigned to one of the front panel knobs.
1. St.Compressor (Stereo Compressor)
This effect compresses the input signal to regulate the
level and give a “punchy” effect. This is useful when ap-
plied to sounds that have a strong attack.
If using this for the master effect, you can link the left
and right channels or make them operate independent-
ly.
Dry/Wet
[Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
Env Sel (Envelope Select)
only MFX
[LR Mix, LR Indv.]
When L/R Mix is selected for this parameter, the left
and right channels are linked to control the Limiter us-
ing the mixed signal.
With L/R individually, the left and right channels con-
trol the Limiter individually.
You can switch between LR Mix and LR Indiv. set-
tings only when using this effect type for the mas-
ter effect. When using this effect type for an insert
effect, this parameter is fixed at LR Mix.
Sens (Sensitivity)
[001…127]
The “Sensitivity” parameter sets the sensitivity of the
compressor. If this parameter is set to a higher value,
lower level sounds will be boosted. With a higher Sensi-
tivity, the overall volume level is higher. To adjust the fi-
nal volume level, use the “Output Level” parameter.
Attack [0000.1…0500.0ms]
Sets the attack level.
OutLevel (Output Level)
[000…127]
This parameter controls the output level.
2. St.Limiter (Stereo Limiter)
The Limiter regulates the input signal level. It is similar
to the Compressor, except that the Limiter compresses
only signals that exceed the specified level to lower un-
necessary peak signals. If using this for the master effect,
you can link the left and right channels or make them
operate independently.
Dry/Wet
[Dry, 99:1…1:99, Wet]
Sets the balance between the effect and dry sounds.
Env Sel (Envelope Select)
only MFX
[LR Mix, LR Indv.]
☞
p.123 “1. St.Compressor (Stereo Compressor)”
Ratio [1.0:1…50.0:1…Inf:1]
Sets the signal compression ratio.
Threshold [–40…+00dB]
Sets the level above which the compressor is applied.
Compression is applied only when the signal level ex-
ceeds the “Threshold” value.
Left
Right
Dry / Wet
Dry / Wet
Stereo In - Stereo Out
Compressor
Compressor
Envelope Select (IFX: LR Mix)
Output Level
Output Level
Envelope - Control
Envelope - Control
Sensitivity=100
Sensitivity=40
Dry
Wet
Time
Level
Compressor - Sensitivity
Louder
Dry
Wet
Time
Level
Attack=80
Attack=20
Compressor - Attack
Left
Right
Dry / Wet
Dry / Wet
Stereo In - Stereo Out
Limiter
Limiter
Envelope Select (IFX: LR Mix)
Gain Adjust
Gain Adjust
Envelope - Control
Envelope - Control
Trigger Monitor
+
Input Level
Output Level
Threshold
Ratio=1.0 : 1
Ratio=2.0 : 1
Ratio=4.0 : 1
Ration=Inf : 1
Louder
Louder
Time
Level
Threshold
Ratio=Inf : 1
Ratio=2.0 : 1
Ratio=4.0 : 1
Dry
Ratio=1.0 : 1
Limiter - Threshold / Ratio
Summary of Contents for MMT RADIAS
