Korg MMT RADIAS, Owner'S Manual, Page: 17 / 176

Front panel
11
7. UNISON
[UNISON - FRMNT REC] button
UNISON: Switches the unison function on/off.
FRMNT REC: When editing vocoder settings, this
records format motion data for use with the Formant
Motion function.
8. MIXER
[OSC1 - SCR1] knob
OSC 1: Adjusts the volume of oscillator 1.
SCR 1: When editing vocoder settings, this adjusts the
volume of input 1 (timbre) to the carrier.
[OSC2 - SRC2] knob
OSC 2: Adjusts the volume of oscillator 2.
SCR 1: When editing vocoder settings, this adjusts the
volume of input 2 (e.g., external input) to the carrier.
[NOISE] knob
Adjusts the volume of the noise generator.
9. FILTER 1
[CUTOFF - FC OFFSET] knob
CUTOFF: Adjusts the cutoff frequency of filter 1.
FC OFFSET: When editing vocoder settings, this adjusts
the cutoff frequency offset value of the synthesis filter.
[RESONANCE] knob
RESONANCE: Adjusts the resonance of filter 1.
RESONANCE: When editing vocoder settings, this ad-
justs the resonance of the synthesis filters.
[TYPE] knob
Selects the type of filter used by filter 1.
A position between markings will produce a character
mid-way between the two filter types, allowing you to
adjust the proportion of the two types.
[ROUTING - MODULATOR] button
ROUTING: This specifies the routing (combination) of
filters 1 and 2.
MODULATOR: When editing vocoder settings, this se-
lects the modulator.
10. FILTER 2
[CUTOFF - THRESHOLD] knob
CUTOFF: Adjusts the cutoff frequency of filter 2.
THRESHOLD: When editing vocoder settings, this ad-
justs the threshold level of the modulator input signal.
[RESONANCE - HPF LEVEL] knob
RESONANCE: Adjusts the resonance of filter 2.
HPF LEVEL: When editing vocoder settings, this adjusts
the output level of the HPF (High Pass Filter) applied to
the modulator input signal (e.g., the INPUT 2 jack).
[TYPE - FRMNT SHIFT] button
TYPE: Selects the type of filter used by filter 2.
FRMNT SHIFT: When editing vocoder settings, this ad-
justs the amount of formant shift.
11. FILTER COMMON
[SELECT] button
Selects which filter will be affected by adjusting the EG1
INT knob and KEY TRACK knob.
The LED corresponding to the filter you select will light.
[EG1 INT - FC MOD INT] knob
EG 1 INT: Adjusts the amount of EG1 (depth) that will
be applied to the filter cutoff frequency.
FC MOD INT: When editing vocoder settings, this ad-
justs the depth of modulation applied to the cutoff fre-
quency of the synthesis filter. The modulation source is
selected by the [SOURCE - FC MOD SRC] button of the
Virtual Patch section.
[KEY TRACK - E.F.SENS] knob
KEY TRACK: Adjusts the amount of keyboard tracking
that will be applied to the filter. This allow notes played
higher on the keyboard to have a different filter cutoff
than notes played lower on the keyboard.
E.F. SENS: When editing vocoder settings, this adjusts
the sensitivity of the envelope follower in the vocoder
section.
12. AMP
[LEVEL - VC LEVEL] knob
LEVEL: Adjusts the volume of the selected timbre.
VC LEVEL: When editing vocoder settings, this adjusts
the output level of the vocoder.
[PAN - DIRECT LEVEL] knob
PAN: Adjusts the pan position of the selected timbre.
DIRECT LEVEL: When editing vocoder settings, this ad-
justs the direct output level of the modulator (e.g., IN-
PUT 2 jack).
[DEPTH] knob
Adjusts the depth of the DRIVE/WS (Wave Shape) ef-
fect.
[DRIVE/WS - HPF GATE] button
DRIVE/WS: Selects which function will be applied to
the timbre. The LED for the selected function will light.
HPF GATE: When editing vocoder settings, this speci-
fies whether the High Pass Frequency gate is enabled or
disabled (on or off).
13. V.PATCH (VIRTUAL PATCH)
[SELECT] button
Selects the patch that you will be editing. The LED of the
selected patch will light.
[SOURCE - FC MOD SRC] button
SOURCE: Selects the modulation source.
FC MOD SRC (Filter Cutoff Modulation Source): When
you’re editing vocoder settings, this selects the modula-