Korg MMT RADIAS, Owner'S Manual, Page: 98 / 176

Program parameters
92
Velocity
Keyboard velocity (playing dynamics) will be the mod-
ulation source.
P.Bend
Pitch bend will be the modulation source.
M.Wheel
Modulation wheel will be the modulation source.
KeyTrack
Keyboard tracking (position) will be the modulation
source.
Keyboard tracking works according to the pitch as
controlled by pitch bend, transpose, and modula-
tion sequencer. It does not reflect pitch changes
produced by vibrato or virtual patching.
EnvF
The envelope data obtained from the envelope follower
will be the modulation source.
MIDI1, MIDI2, MIDI3, MIDI4, MIDI5
The function specified for the Global mode P04: MIDI
page parameters “MIDI1,” “MIDI2,” “MIDI3,”
“MIDI4,” or “MIDI5” will be the modulation source.
2: Dest (Destination)

DESTINATION

[Pitch…LFO2Freq]
Selects the parameter that will be the modulation desti-
nation.
Pitch
The pitch of the entire timbre will be modulated.
OSC2Pitch
The P06–2: OSC/MIXER – OSC2 tab page “Tune” pa-
rameter will be modulated.
OSC1Ctrl
The P06–1: OSC/MIXER – OSC1 tab page “Control1”
parameter will be modulated.
OSC1Level, OSC2Level, NoiseLvl
The P06–3: OSC/MIXER – MIXER tab page “OSC1 Lvl,”
“OSC2 Lvl,” or “NoiseLvl” parameter will be modulat-
ed.
Filt1Type
The P07–1: FILTER – FILTER1 tab page “Type” parame-
ter will be modulated.
Filt1Cut
The P07–1: FILTER – FILTER1 tab page “Cutoff” param-
eter will be modulated.
Filt1Reso
The P07–1: FILTER – FILTER1 tab page “Resonance” pa-
rameter will be modulated.
Filt2Cut
The P07–2: FILTER – FILTER2 tab page “Cutoff” param-
eter will be modulated.
Drv/WsDpt
The P08–1: AMP page “Depth” parameter will be mod-
ulated.
AmpLevel
The P08–1: AMP page “Level” parameter will be modu-
lated.
Pan
The P08–1: AMP page “Pan” parameter will be modulat-
ed.
LFO1Freq
The P10–1: LFO – LFO1 tab page “Freq” parameter will
be modulated.
LFO2Freq
The P10–2: LFO – LFO2 tab page “Freq” parameter will
be modulated.
If “TempoSync” is turned On for LFO1 or LFO2,
selecting LFO1Freq or LFO2Freq respectively will
have no effect.
3: Intensity

INTENSITY

[–63…+63]
Specifies the depth of the modulation produced by the
modulation source.
If this is set to 0, no modulation will occur.
P12 MOD SEQ
(Modulation Sequencer)
These are the parameters for the Modulation Sequenc-
ers. Modulation sequencers apply time-varying change
to the sound parameters in a way similar to the analog
sequencers of the past. Three modulation sequencers are
provided for each timbre.
P12–1: COMN (SEQ Common)
1: LastStep [01…16]
Specifies the length of the sequence in steps (i.e., the
maximum number of steps).
2: SeqType (Sequence Type) [Forward…Alt2]
Specifies the sequence type (the direction in which the
sequence will play).
Forward
Play from the first step (Step01).
Step
01
Step
02
Step
03
Step
14
Step
15
Step
16
Forward (Last Step=16)
Run Mode=Loop