Appendices
148
In order for channel aftertouch messages to be transmit-
ted and received, the Global mode P06: MIDI FILTER
page “CtrlChg” and the Program Edit mode P03–4:
TIMBRE – MIDI tab page “AT” must both be set to
(enabled). If either of these parameters are set to
✕
(dis-
abled), channel aftertouch will not be transmitted or re-
ceived.
Pitch bend
Pitch bend change [En, bb, mm]
(n: channel, bb: lower byte of value, mm: upper byte of
value)
When pitch bend change messages are received, pitch
bending will be applied according to the Program Edit
mode P05: PITCH page “BendRange” setting. You can
also select pitch bend as the modulation source for a vir-
tual patch or for vocoder FC MOD. In this case, pitch
bend messages will operate as a modulation source that
controls the target parameter over a range of –127 –
+127, with mm=64 and bb=00 as the zero (center) value.
(These messages are received on the MIDI channel of the
timbre.)
When you operate the RADIAS’ pitch bend wheel,
pitch bend change messages are transmitted on the
MIDI channel of the selected timbre.
In order for pitch bend change messages to be transmit-
ted, the Global mode P06: MIDI FILTER page “Pitch-
Bend” and the Program Edit mode P03–4: TIMBRE –
MIDI tab page “PBnd” parameters must both be set to
(enabled). If either of these parameters are set to
✕
(dis-
abled), pitch bend changes will not be received.
These messages are transmitted according to the Global
mode P06: MIDI FILTER page “PitchBend” setting.
Control change
Control change [Bn, cc, vv]
(n: channel, cc: control change number, vv: value)
These messages are transmitted and received with a va-
riety of different control change numbers, such as for the
modulation wheel or a modulation source (MIDI1,
MIDI2, MIDI3, MIDI4, MIDI5).
The Global mode P06: MIDI Filter page “Ctrl Chg” set-
ting enables or disables overall transmission and recep-
tion of all MIDI control change messages. Within a
program, the Program Edit mode P03–5, 6: TIMBRE –
CC-A, CC-B tab pages let you enable/disable reception
of various types of control change for each timbre.
Modulation depth (CC#01) [Bn, 01, vv]
When modulation depth messages are received, the in-
tensity of vibrato produced by LFO2 will change accord-
ing to the Program Edit mode P05: PITCH page
“VibraInt” setting. If the maximum value (127) is re-
ceived, vibrato will apply at the pitch range specified by
“VibraInt.” If the minimum value (0) is received, no vi-
brato will apply.
When you operate the RADIAS’ modulation wheel,
modulation depth messages are transmitted on the
MIDI channel of the selected timbre.
Volume (CC#07) [Bn, 07, vv]
If the Global mode P08: PEDAL/SW page “A.Pedal” is
set to Volume, volume messages will be transmitted on
the MIDI channel of the selected timbre when you oper-
ate the pedal. If the Global mode P07: MIDI MAP [CC#]
page “AmpLevel” is assigned to volume (CC#07), in-
coming volume messages will control the volume.
Panpot (CC#10) [Bn, 0A, vv]
If the Global mode P08: PEDAL/SW page “A.Pedal” is
set to Pan, pan messages will be transmitted on the MIDI
channel of the selected timbre when you operate the
pedal. If the Global mode P07: MIDI MAP [CC#] page
“Pan” is assigned to pan (CC#10), incoming pan mes-
sages will control the stereo panning of the output.
Expression (CC#11) [Bn, 0B, vv]
When expression messages are received, the volume of
a timbre will be controlled. The volume will be at maxi-
mum if the maximum value (127) is received, and at zero
if the minimum value (0) is received.
If the Global mode P08: PEDAL/SW page “A.Pedal” is
set to ExpPedal, expression messages will be transmit-
ted on the MIDI channel of the selected timbre when you
operate the pedal.
Damper pedal (CC#64) [Bn, 40, vv]
When damper pedal messages are received, the damper
effect (hold) of a timbre will be switched on/off.
If the Global mode P08: PEDAL/SW page “A.SwFunc”
is set to Damper, damper messages (0: off, 7F: on) will be
transmitted on the MIDI channel of the selected timbre
when you operate the pedal switch.
Portamento (CC#65) [Bn, 41, vv]
When portamento messages are received, the portamen-
to effect of a timbre will be switched on/off. If the por-
tamento time is set to 0, there will be no portamento
effect.
If the Global mode P08: PEDAL/SW page “A.SwFunc”
is set to PortSw, portamento messages (0: off, 7F: on) will
be transmitted on the MIDI channel of the selected tim-
bre when you operate the pedal switch.
Using control changes as modulation
sources for virtual patches
By setting the Global mode P04: MIDI page “MIDI1,”
“MIDI2,” “MIDI3,” “MIDI4,” and “MIDI5” to CC#cc
(cc=00–95/102–119) you can use control change messag-
es as modulation sources for virtual patches or as the vo-
coder FC MOD modulation source. The value (0–127) of
the message is used without change as the modulation
source. No distinction is made between upper byte
(MSB)/lower byte (LSB) or between continuous-type
and switch-type messages.
Summary of Contents for MMT RADIAS
