Husqvarna F2203P4 Repair Manual Download Page 26

Page: 26 / 381

6 FORK, TRIPLE CLAMP

•

R00028-10

R00029-10

- Pull sleeve

out of the reservoir.

- Remove spring@) with preload spacers@).

- Remove seal rings Ci) and O-ring

G,.

- Remove pilot bushings«&.

Disassembling the �iston rod

Info

The steps are identical for both fork legs, except for the hydrostop needle and valve.

R00038-10

Preparatory work

- Disassemble the fork legs. (

!i.,!I

p. 20)

- Remove the spring. (

!i.,!I

p. 22)

- Disassemble the cartridge. (

!i.,!I

p. 23)

Main work

- Degrease hydrostop needle

and clamp using the special

tool.

I Clamping stand (T1202S) (

!i.,!I

p. 367)

- Release hydrostop needle

and remove it from the piston

rod.

✓ Valve

usually remains in the hydrostop needle.

Info

silver hydrostop needle on compression damp

ing side.

red hydrostop needle on rebound damping side.

- Turn piston rod, degrease and clamp using the special tool.

I Clamping stand (T14049S) (

!i.,!I

p. 370)

- Remove rebound shim stack

@).

- Remove piston

C,.

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands