Husqvarna F2203P4 Repair Manual Download Page 203

Page: 203 / 381

- Remove shaft seal ring

of the crankshaft.

18 ENGINE

- Press the new shaft seal ring all the way in with the open side

facing outward.

•

Info

Provide suitable support for the clutch cover while

pressing in.

- Mount lock ring

- Blow out the oil channel with compressed air and check that

it is clear.

18.4.4

Checking the oil pressure regulator valve

8-1

o-8

-0

o-8

305033-10

200155-10

305033-10

- Remove screw plug

with sealing washer

Remove pressure spring

and ball

e .

- Measure the spring length of the oil pressure regulator valve.

Oil pressure regulator valve

Minimum length of pres- 123.5 mm (0.925 in)

sure spnng

If the measured value does not meet specifications:

- Change the spring.

- Check ball

and the sealing seat.

If there is damage or wear:

- Change the ball and machine the sealing seat.

- Install ball

and pressure spring

CD.

Mount and tighten screw plug

with sealing washer

Guideline

Plug, oil pressure

regulator valve

M12x1 .5

20 Nm (14.8 lbf ft)

201

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands