manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 153

16  BRAKE SYSTEM 

Info 

Clean up overflowed or spilled brake fluid immedi­
ately with water. 

Checking the free travel of the hand  brake lever 

Warning 

Danger of accidents 

The brake system fails in the event of overheating. 

If there is no free travel on the hand brake lever, pressure builds up on the front brake circuit. 

-

Set the free travel on the hand brake lever in accordance with the specification.

(FE EU/ AU,  FE 350 S US) 

-

Push the hand brake lever to the handlebar and check

free travel  f).

Free travel of hand brake 

lever 

� 3 mm(� 0.12 in)

If the free travel does not match the specification: 

- Adjust the free travel of the hand brake lever.

(

� 

p. 152)

(FE 350 US) 

-

Push the hand brake lever forward and check free

travel  f).

Free travel of hand brake 

lever 

� 3 mm(� 0.12 in)

If the free travel does not match the specification: 

- Adjust the basic position of the hand brake lever.

(

� 

p. 151)

Adjusting the basic �osition of the hand  brake lever {FE 350 US) 

H00198-10 

-

Check the free travel of the hand brake lever. (

� 

p. 151)

- Adjust the basic setting of the hand brake lever to your hand

size by turning adjusting screw 

O.

Info 

Turn the adjusting screw clockwise to increase the 
distance between the hand brake lever and the han­
dlebar. 
Turn the adjusting screw counterclockwise to 
decrease the distance between the hand brake lever 
and the handlebar. 
The range of adjustment is limited. 
Turn the adjusting screw by hand only,  and do not 
apply any force. 

Do not make any adjustments while riding! 

.. 

.. 

.. 

151 

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands