manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 171

401914-01 

Checkin  the headli 

400726-10 

17.7 

Adjustin  the headli 

17  LIGHTING SYSTEM, INSTRUMENTS 

Switching off the service interval display 

-

Press and hold the left button.

✓

off 

appears on the display.

-

Position the vehicle upright on a horizontal surface in front of

a light wall and make a mark at the height of the center of the
low beam headlight.

-

Make another mark at a distance 

Cs) 

under the first mark.

Guideline

I 

Distance 

Cs)

15 

cm (2 in)

-

Position the vehicle vertically at a distance 

t) 

away from the

wall.

Guideline

I 

Distance 

e

15 

m (16 ft)

- The rider now sits down on the motorcycle.
-

Switch on the low beam.

-

Check the headlight setting.

The boundary between light and dark must be exactly on
the lower mark for a motorcycle with rider.

If the light-dark  border does not meet specifications: 

- Adjust the headlight range.  (

0 

p.  169)

Preparatory work 

-

Check the headlight setting.  (

0 

p.  169)

Main work 

(FE EU/AU,  FE 350 US) 

-

Loosen screw 

O.

-

Adjust the headlight range by pivoting the headlight.

Guideline

The boundary between light and dark must be exactly 
on the lower mark for a motorcycle with driver (instruc­
tions on how to apply the mark:  Checking the headlight 
setting). 

Info 

If you have a payload,  you may have to correct the 

headlight range. 

-

Tighten screw 

O.

169 

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands