Husqvarna F2203P4 Repair Manual Download Page 135

Page: 135 / 381

14 WHEELS

(FE EU/AU, FE 350 US)

Check that the chain guide is firmly seated.

If the chain guide is loose:

Tighten the screws on the chain guide.

Guideline

Remaining

10 Nm

screws, chassis

(7.4 lbf ft)

Remaining nuts,

10 Nm

chassis

(7.4 lbf ft)

(FE 350 SUS)

Check that the chain guide is firmly seated.

If the chain guide is loose:

Tighten the fitting on the chain guide.

Guideline

Remaining

10 Nm

screws, chassis

(7.4 lbf ft)

Remaining nuts,

10 Nm

chassis

(7.4 lbf ft)

Finishing work

Remove the motorcycle from the lift stand. (

�

p. 13)

14.8.7

Checking for chain dirt accumulation

400678-01

Check the chain for coarse dirt accumulation.

If the chain is very dirty:

Clean the chain. (

�

p. 133)

14.8.8

Cleaning the chain

Warning

Danger of accidents

Oil or grease on the tires reduces the road grip.

Remove the lubricant from the tires using a suitable cleaning agent.

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

- Always keep the brake discs free of oil and grease.
-

Clean the brake discs with brake cleaner when necessary.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

133

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands