Husqvarna F2203P4 Repair Manual Download Page 108

Page: 108 / 381

12 FUEL TANK, SEAT, TRIM

305313-10

305314-10

305313-10

305314-10

106

Main work

- Remove nut

with the gasket.

- Remove fuel connection

with the gasket.

- Remove screws

fD.

- Pull out the fuel pump.

- Position the fuel pump.

- Mount fuel connection

with the gasket but do not tighten

yet.
Guideline

Fuel connection on

fuel pump

10 Nm (7.4 lbf ft)

- Mount and tighten nut

with the gasket.

Guideline

Nut, fuel pump fixa-

M 12

tion

- Tighten fuel connection

Guideline

Fuel connection on

fuel pump

- Mount and tighten screws

fD.

Guideline

I Screw, fuel pump

EJOT PT

15 Nm (11 .1 lbf ft)

10 Nm (7.4 lbf ft)

12.3 Nm (1.7 lbf ft)

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands