manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 264

21  LUBRICATION SYSTEM 

Adding engine oil 

Info 

-

Remove the oil filler plug  @  with the 0-ring from the clutch

cover and fill up with engine oil.

Engine oil 

•

Info

1.0 I  (1.1 qt.) 

Engine oil 

(SAE 1 0W/50) 
(

a 

p. 352) 

I 

Too little engine oil or poor-quality engine oil results in 
premature wear to the engine. 

-

Install and tighten the oil filler plug with 0-ring.

Danger 

Danger of poisoning 

Exhaust gases are toxic and 

inhaling them may result in unconsciousness and 
death. 
-

Always make sure there is sufficient ventilation
when running the engine.

-

Use an effective exhaust extraction system when

starting or running the engine in an enclosed
space.

-

Start the engine and check that it is oil-tight.

Finishing work 

-

Check the engine oil level. (

a 

p. 259)

-

Install the engine guard. (

a 

p. 48)

.. 

Too little engine oil or poor-quality engine oil results in premature wear of the engine. 

262 

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands