manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 129

14  WHEELS 

Main work 

- Check the wheel bearing for damage and wear.

If the wheel bearing is damaged or worn: 

Change the rear wheel bearing. (

I!!;,! 

p. 136) 

- Clean and grease shaft seal rings 

O 

and contact surface 

6)

of the spacers.

I 

Long-life grease (

I!!;,! 

p. 354) 

- Insert the spacers.

(FE  EU/ AU,  FE  350 US) 

Clean and grease the wheel spindle. 

I  Long-life grease (

llill 

p. 354) 

- Position the rear wheel and insert wheel spindle 

8.

- Mount the chain.

✓ The brake linings are correctly positioned.

- Position chain adjuster@). Mount nut 

C,, 

but do not

tighten it yet.

- Make sure that chain adjusters 

(s) 

are fitted correctly on

adjusting screws 

0.

- Check the chain tension. (

0 

p. 129)

- Tighten nut 

C,.

Guideline

M20x1.5 

80  Nm (59 lbf ft) 

Info 

The wide adjustment range of the chain adjusters 

(32 mm (1 .26 in)) enables different secondary 

ratios with the same chain length. 

Chain adjusters 

(s) 

can be turned by 180

°

. 

- Operate the foot brake lever repeatedly until the brake

linings are in contact with the brake disc and there is a

pressure point.

(FE  350 SUS) 

- Clean and grease the wheel spindle.

I  Long-life grease (

I!!;,! 

p. 354)

- Position the rear wheel and insert wheel spindle 

8-

- Mount the chain.

✓ The brake linings are correctly positioned.

127 

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands