Husqvarna F2203P4 Repair Manual Download Page 201

Page: 201 / 381

400996-01

18.4.3

Work on the clutch cover

G00444-10

G00445-10

18 ENGINE

Press in shaft seal ring

of the countershaft so it is flush

with the open side facing in.

Mount and tighten oil nozzle (D.

Guideline

Oil nozzle, pis
ton cooling

Position all bearing retainers.

Mount and tighten screws

C,.

Guideline

Locking screw

for bearing

2 Nm (1.5 lbf ft)

Loctite

243

™

6 Nm (4.4 lbf ft)

Loctite

243

™

Blow out the oil channel with compressed air and check that

it is clear.

Remove shaft seal ring

Remove lock ring

Remove shaft seal ring (D.

199

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands