Husqvarna F2203P4 Repair Manual Download Page 270

Page: 270 / 381

23 CYLINDER HEAD

23.1

Checking the valve clearance

268

Preparatory work

(FE EU/AU, FE 350 US)

- Remove the seat. (

lll:!l

p. 97)

- Remove the fuel tank. (

lll:!l

p. 98)

(FE 350 SUS)

- Remove the seat. (

lll:!l

p. 97)

- Remove the fuel tank. (

lll:!l

p. 98)

- Remove the activated charcoal filter. (

lll:!l

p. 108)

Main work

- Push back cover

disconnect the connector.

- Disconnect spark plug connector @.

Remove the spark plug with special tool

I Spark plug wrench with link (77229172000) (

l!!l

p. 366)

- Remove right radiator shield

Remove screws

Pivot the radiator forward slightly on the right.

- Remove fittings

CD.

Take off the engine braces.

- Push back hose clamp @.

- Pull off the air release hose.

- Remove screws @.

- Remove the valve cover with the gasket to the right.

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands